background image

3

Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.

Used without the safety alert symbol indicates potentially hazardous situation which, if not avoided, may
result in property damage.

It is important for you to read and understand this manual. The information it contains relates to protecting YOUR
SAFETY and PREVENTING PROBLEMS. The symbols below are used to help you recognize this information. 

SAFETY GUIDELINES - DEFINITIONS

SOME DUST CREATED BY POWER SANDING, SAWING, GRINDING, DRILLING, AND OTHER

CONSTRUCTION ACTIVITIES 

contains chemicals known to cause cancer, birth defects or other reproductive harm.

Some examples of these chemicals are:
·  lead from lead-based paints,
· crystalline silica from bricks and cement and other masonry products, and
·  arsenic and chromium from chemically-treated lumber. 
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to
these chemicals: work in a well ventilated area, and work with approved safety equipment, always wear 

MSHA/NIOSH

approved, properly fitting face mask or respirator when using such tools.

CALIFORNIA PROPOSITION 65

Содержание ShopMaster JT160






















Отзывы: