background image

9

SAFETY INSTRUCTIONS FOR CHARGER 

AND BATTERIES

1.

SAVE THESE INSTRUCTIONS.

This manual contains important safety 

and operating instructions for Delta Battery Charger.

2.

Before using a battery charger,

read all instructions and cautionary 

markings on (1) battery charger, (2) battery pack, and (3) product using 
battery. 

3.

To reduce risk of injury, a Delta charger should only be 

used to charge a Delta battery pack. Other types of batteries may burst 
causing personal injury and damage. Do not charge a Delta battery pack
with any other charger.

4.

Do not expose charger

to rain, snow or frost. 

5.

Do not abuse cord.

Never carry charger by cord or yank it to 

disconnect from receptacle. Pull by plug rather than cord when 
disconnecting charger. Have damaged or worn power cord and strain 
reliever replaced immediately. DO NOT ATTEMPT TO REPAIR POWER 
CORD. 

6.

Make sure cord

is located so that it will not be stepped on, tripped 

over, or otherwise subjected to damage or stress.

7.

Do not use an extension cord

unless absolutely necessary. Use of 

improper extension cord could result in a risk of fire and electric shock. 
If an extension cord must be used, make sure:
A. That the pins on plug of extension cord are the same number, size
and shape as those of plug on charger.
B. That the extension cord is properly wired and in good electrical
condition.
C. Wire Size of cord is at least as specified in following chart:

D. If an extension cord is to be used outdoors it must be marked with
the suffix W-A or W following the cord type designation. For example –
SJTW-A to indicate it is acceptable for outdoor use.

8.

Do not operate

charger with damaged cord or plug – have them replaced 

immediately, to avoid a hazard. DO NOT ATTEMPT TO REPAIR POWER 
CORD.

9.

Do not operate

charger if it has received a sharp blow, been dropped, or 

otherwise damaged in any way; take it to a qualified serviceman.

10. Do not disassemble charger or battery pack.

Take it to a qualified 

serviceman when service or repair is required. Incorrect reassembly may
result in a risk of electric shock or fire.

11. Unplug charger

from outlet before attempting any maintenance or 

cleaning – to reduce risk of electric shock.

12. Charge the battery pack

in a well ventilated place, do not cover the 

charger and battery pack with a cloth, etc., while charging.

13. Do not store

the charger or battery pack in locations where the 

temperature may reach or exceed 122°F (50°C) (such as a metal tool 
shed, or a car in the summer), which can lead to deterioration of the 
storage battery.

LENGTH OF CORD IN FEET

25

50

100

150

AWG SIZE OF CORD

18

18

18

16

Содержание ShopMaster CL180BN


















Отзывы: