background image

18

Fig. 45

Fig. 46

Fig. 47

RAISING AND
LOWERING SPINDLE

The spindle can be raised or lowered by loosening lock
knob (A) Fig. 45, and turning handwheel (B). To raise the
spindle height, turn the handwheel (B) clockwise. To lower
the spindle height, turn handle (B) counterclockwise.

The scale (C) Fig. 45, indicates the spindle travel range
from 0 to 3 and is marked in 1/16 increments. Minor cut-
ter height adjustments can be measured using the point-
er (D) along the scale (C).

CAUTION:

Always tighten lock

knob (A) after adjusting spindle height.

CHANGING SPEEDS AND
ADJUSTING BELT TENSION

The shaper is supplied with a 2-step motor pulley and
a 2-step spindle pulley that provides spindle speeds of
7,000 and 10,000 R.P.M. When the belt is on the largest
step of the motor pulley and the smallest step of the
spindle pulley, the spindle speed will be 10,000 R.P.M.
When the belt is on the smallest step of the motor pulley
and the largest step of the spindle pulley, the spindle
speed will be 7,000 R.P.M.

A chart (Y) Fig. 46, illustrating the correct belt placement
for 7,000 or 10,000 R.P.M. is located on the inside panel
of the motor access door.

To change speeds and adjust belt tension, proceed as
follows:

1.

DISCONNECT THE MACHINE FROM THE POWER

SOURCE

and open motor access door, as shown in Fig. 46.

2.

Loosen thumb screw lock (A) Fig. 47. Release ten-

sion on belt by moving lever (B), to the left. Position belt
(C), on the desired steps of the spindle pulley (D), and
the motor pulley (E), and apply belt tension by moving
lever (B), to the right. When desired belt tension is
applied to belt, retighten thumb screw lock (A).

3.

Proper belt tension is attained when there is approxi-

mately 3/32 deflection using light finger pressure (approx.
3.5 lbs.) at the center of the belt span between pulleys (D)
and (E) Fig. 47.

IMPORTANT:

Pulleys (D) and (E) should

always be aligned with each other to provide maximum
belt performance and reduce belt wear. To check pulley
alignment, refer to section 

“REPLACING SPINDLE CAR-

TRIDGE.”

REVERSING
SPINDLE ROTATION

MAKE CERTAIN THE MACHINE IS DISCONNECTED
FROM THE POWER SOURCE

.

The motor is equipped with a reversing switch (X) Fig. 46,
which is located on the motor junction box.

CAUTION:

Never attempt to reverse the rotation of the spindle with
the motor running.

X

Y

D

C

A

B

C

E

D

B

A

Содержание Platinum Edition 43-420





























Отзывы: