Delta Controls
Document Edition 1.9
Page 7 of 12
Use the arrow buttons to navigate through the menu options. Once you have navigated to the desired item you
wish to display or change, wait a brief moment for the current value to begin blinking, whereby you can use the
arrow buttons to make any necessary changes. Once the changes are made or you wish to move on, press E
NTER
.
3.
Configuration Menu Options
The Configuration Menu is a list of items which you can navigate through and make changes to as you need for
setup purposes. You may use either the down arrow or the up arrow to navigate through the menu items (in
direct or reverse order). Waiting momentarily on an item will eventually display the current setting and allow
you to make changes. The Configuration Menu items are as follows:
Menu Item
Description
CFg
CFg
CFg
CFg
Displayed momentarily to indicate you have successfully entered the Configuration
Menu.
DEG
DEG
DEG
DEG
The Temperature Units Setting (C or F).
DSP
DSP
DSP
DSP
The LCD Display Code Setting (AV15) configures local display and button
handling and has the following definitions:
1.0
No Value. The LCD & buttons are fully available for remote programming.
2.0
Local Temperature (AI1) only is always displayed.
3.0
Local Setpoint (AV6) only is always displayed, and can be adjusted.
4.0
Temperature is displayed by default, and pressing an arrow button displays
the Setpoint for adjustment.
5.0
Temperature and Setpoint are alternated on the display every 2 seconds, until
pressing an arrow button displays just the Setpoint for adjustment.
6.0
Setpoint only is always displayed, but cannot be adjusted.
7.0
Temperature is displayed by default, and pressing an arrow button displays
the Setpoint for 3 seconds but cannot be adjusted.
8.0
Temperature and Setpoint are alternated on the display every 2 seconds, but
the Setpoint cannot be adjusted.
N
OTE
: When connected to LINKnet the Display Code should be set to 1.0 (whereby
the display and buttons are controlled through GCL in the host DAC device), while
a setting of 4.0 is a typical choice when connected directly to an MS/TP network.
Lnt
Lnt
Lnt
Lnt
The LINKnet Communications Setting (On or Off), to match the connection
method. When turned On the network communications is set to LINKnet, and when
Off the communications is set to MS/TP.
dNA
dNA
dNA
dNA
The DNA Setting (On or Off), for inheriting a derived address from higher-up
devices on an MS/TP network, or not.
Add
Add
Add
Add
The device Address (1 to 99), which is used internally as the MAC Address. As the
BACstat can only be a Subnet device on MS/TP, this address is always mapped in as
the Subnet value. On LINKnet, this address is the physical address for the device
(limited to 1 to 12) and the other address settings are irrelevant. Note: On MS/TP
the complete BACnet address is in the form of “OEM_Area_System_Subnet”
SYS
SYS
SYS
SYS
The System number (0 to 99), which can only be set manually when on MS/TP and
DNA
is turned off – and is inherited when DNA is on.
ArE
ArE
ArE
ArE
The Area number (0 to 99), which can only be set manually when on MS/TP and
DNA
is turned off – and is inherited when DNA is on.
OEM
OEM
OEM
OEM
The OEM number (0 to 3), which can only be set manually when on MS/TP and
DNA
is turned off – and is inherited when DNA is on.
BAU
BAU
BAU
BAU
The Network Speed (9,600 or 19,200 or 38,400 or 76,800 bps). The default for both
LINKnet and MS/TP is 76,800 bps. While the baud rate for MS/TP devices may
need to be adjusted to suite, the speed for LINKnet networks should remain at
76,800 bps.
