background image

 

1 9

5. MAINTENANCE 

 

 

Normally, the life of battery is 3 years. But extreme operating condition and 

environment may shorten its life-span. 

 

To replace batteries, contact qualified personnel. 

 

When UPS has been unused for a period of time, the batteries will discharge 

slightly. It is recommended to charge the UPS once every 3 months. 

 

Use a vacuum cleaner to get rid of any dust that may rest on the opening of 

the fan. 

 

Unplug the UPS when it is not used for a long time. 

 

When cleaning the plastic case or front panel, only use a soft, dry cloth. If the 

case or front panel is very dirty, use a neutral, non-abrasive detergent. Do not 
use alcohol or ammonia based solutions. 

 

When moving your UPS, always handle it with care. 

 

Avoid spilling liquid on the UPS. 

 

The equipment should be repaired and installed by individuals with previous 

training. 

When installing this equipment, it should be noted that the leakage current of the 
UPS and its loads must not exceed 3.5mA in total for safety. 

 

6. PLACEMENT 

You can set the UPS on the Rack , You can make the UPS Erect by the Support 
stands also. 

To stably install the UPS of 1 & 2 & 3kVA models, you must set up UPS with 
supporting stands. 

The installation method is as shown below: 

 

 
 
 
 
 
 
 
 
 
 
 
 

 

Fig 6-1 Erect the UPS with supporting stands

 

Содержание 1KVA


























Отзывы: