Delta Tau ACC-24E2S Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 45

background image

Accessory 24E2S

Ultralite/MACRO Station Setup

23

The PMAC2 Style outputs allow the PMAC to control up to three individual output channels based on the
mode. These outputs are described as output A, output B, and output C.

MSn, MI916

Output Description

Typical Use

0

A, B, and C are PWM

Direct PWM Mode only

1

A and B are DAC, C is PWM



10V Outputs for torque, velocity and sinusoidal input amplifiers

2

A and B are PWM, C is PFM

Stepper Systems

3

A and B are DAC, C is PFM



10V Outputs with MLDT Feedback

The default output at the MACRO Station is PWM (MSn,I916=0).

MACRO Station Encoder Conversion Table (MSn,MI120-MI151)

At power-up, the MACRO Station will set up all of the key memory locations and MI-Variables
automatically based on the SW1 connector and firmware of the MACRO Station. The key variables setup
at power-up are the encoder conversion table, servo output registers, and flag input registers.

Encoder Conversion Table for Acc-24E2 at MACRO Station

MS0,MI120=$00C040

;output at X:$0010 at MACRO Station (encoder 1)

MS0,MI121=$00C048

;output at X:$0011 at MACRO Station (encoder 2)

MS0,MI122=$00C050

;output at X:$0012 at MACRO Station (encoder 3)

MS0,MI123=$00C058

;output at X:$0013 at MACRO Station (encoder 4)

MS0,MI120=$00C060

;output at X:$0014 at MACRO Station (encoder 5)

MS0,MI121=$00C068

;output at X:$0015 at MACRO Station (encoder 6)

MS0,MI122=$00C070

;output at X:$0016 at MACRO Station (encoder 7)

MS0,MI123=$00C078

;output at X:$0017 at MACRO Station (encoder 8)

Using Acc-24E2S with the MACRO Station/Ultralite or Turbo Ultralite
Change Output Mode to PFM on the Third Channel

MSn, MI916 = 2 or 3

1.

Change Encoder decode to read Pulse and Direction (if using simulated feedback):

MSn, MI910 = 8

2.

Change PID gains as specified in the Acc-24E2S Manual.

3.

Change Motor Command Output Address at the Ultralite (Ix02) or Turbo Ultralite (Ixx02) to pulse
and direction output.

PMAC2 Ultralite

Motor Node

Address

Motor

Node

Address

1

0

$C0A2

5

8

$C0B2

2

1

$C0A6

6

9

$C0B6

3

4

$C0AA

7

12

$C0BA

4

5

$C0AE

8

13

$C0BE

PMAC2 Turbo Ultralite MACRO IC0

Motor Node

Address

Motor Node

Address

1

0

$078422

5

8

$078432

2

1

$078426

6

9

$078436

3

4

$07842A

7

12

$07843A

4

5

$07842E

8

13

$07843E

«
...
24
25
26
27
28
...
»

Содержание ACC-24E2S














































Отзывы:

Нет отзывов

Похожие инструкции для ACC-24E2S

Бренд: Udoo Страницы: 7

Бренд: Farallon Страницы: 26

Бренд: Observint Страницы: 11

Бренд: Moxa Technologies Страницы: 19

LoadMaster 1500

Бренд: KEMP Technologies Страницы: 71

Бренд: Hama Страницы: 8

FRDM-STBC-SA9500

Бренд: Freescale Semiconductor Страницы: 2

Бренд: Orban Страницы: 255

SuperServer 5019S-L

Бренд: Supermicro Страницы: 61

Бренд: Time domain Страницы: 64

Бренд: Acces I/O products Страницы: 5

SINUS H PROFInet

Бренд: Enertronica Santerno Страницы: 34

Converter Board R0E5212BACFG00

Бренд: Renesas Страницы: 6

SABVISION NVR32

Бренд: SAB Страницы: 29

NIC-FC730i-Mb-2-32G

Бренд: H3C Страницы: 37

EK-Loop Modulus Series

Бренд: ekwb Страницы: 7

Бренд: ANEP Страницы: 48

Бренд: Konica Minolta Страницы: 31

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды