Delta Elektronika SM15K Series Скачать руководство пользователя страница 3

SAFETY INSTRUCTIONS 

 

SM15K INTERFACES 

3 / 19 

DELTA ELEKTRONIKA B.V. 

rev. Nov. 2019 

 
 
 

 

 

 

 

 

 

This marking shown on the product, its packing or its literature indicates that it should not be disposed with other 
wastes at the end of its working life, but should be collected separately to recycle it responsibly to promote the 
sustainable reuse of material resources.  

WEEE  (Waste Electrical & Electronic Equipment) 

1.13

 

Correct Disposal of this Product 

Applicable in the European Union. 

1.11

 

Removal of (safety) covers   

Safety cover(s) are used to cover potentially hazardous voltages. 
Observe the following when removing safety cover(s):  

 

Switch off the unit. 

 

Disconnect the unit from the mains supply or power outlet. 

 

Wait for 5 minutes to allow internal capacitors to discharge. 

 

Unscrew the screws and remove the cover(s). 

 

Always place the cover(s) back before connecting the unit to the mains supply again. 

1.12

 

 Environmental Conditions 

The Delta Elektronika power supplies safety approval applies to the following operating conditions: 

 

Indoor use 

 

Ambient temperature 

 

: -20 to 50 °C 

 

Maximum relative humidity 

: 95%, non condensing, up to 40 °C 

 

 

 

 

: 75%, non condensing, up to 50 °C  

 

Altitude 

 

 

: up to 2000 m  

 

Pollution degree   

 

: 2 

Содержание SM15K Series




















Отзывы: