background image

DS_S48SA1R812_06012006 

THERMAL CONSIDERATIONS 

 
Thermal management is an important part of the system 
design. To ensure proper, reliable operation, sufficient 
cooling of the power module is needed over the entire 
temperature range of the module. Convection cooling is 
usually the dominant mode of heat transfer. 
 
Hence, the choice of equipment to characterize the 
thermal performance of the power module is a wind 
tunnel. 

 

Thermal Testing Setup 

 
Delta’s DC/DC power modules are characterized in 
heated vertical wind tunnels that simulate the thermal 
environments encountered in most electronics 
equipment. This type of equipment commonly uses 
vertically mounted circuit cards in cabinet racks in which 
the power modules are mounted. 
 
The following figure shows the wind tunnel 
characterization setup. The power module is mounted 
on a test PWB and is vertically positioned within the 
wind tunnel. The space between the neighboring PWB 
and the top of the power module or a heat sink is 
6.35mm (0.25”). 

 

Thermal Derating 

 
Heat can be removed by increasing airflow over the 
module. Figure 18 and 19 show maximum output is a 
function of ambient temperature and airflow rate. To 
enhance system reliability, the power module should 
always be operated below the maximum operating 
temperature. If the temperature exceeds the maximum 
module temperature, reliability of the unit may be 
affected. 

 

Note: Wind Tunnel Test Setup Figure Dimensions are in millimeters and (Inches)

10 (0.4”) 

MODULE 

AIR FLOW 

50.8 (2.0”) 

FACING PWB

PWB 

AIR VELOCITY
AND AMBIENT 

TEMPERATURE 

MEASURED BELOW 

THE MODULE

Figure 17: 

Wind tunnel test setup 

 

 

THERMAL CURVES 

 

Figure 19: 

Output current vs. ambient temperature and air velocity

@V

in

< 60

V

 

 

S48SA1R812(Standard) Output Current vs. Ambient Temperature and Air Velocity

@ Vin < 60V

0

2

4

6

8

10

12

14

65

70

75

80

85

90

95

100

Ambient Temperature (

)

Output Current(A)

Natural

Convection

100LFM

200LFM

300LFM

400LFM

500LFM

600LFM

 

Figure 18:

 Hot spot temperature measured point 

The allowed maximum hot spot temperature is defined at 

110

 

 

 

Содержание 33W Family














Отзывы: