background image

4

NOTES ON ASSEMBLY:

-During the assembly process whenever using screws or bolts, check each by placing the screw/bolt 

on the diagram of the item which is drawn actual size and design. Be sure to use the proper size and 

shape specified in the instructions.

-To assemble this unit you may be required to place the unit on it’s side and face. It is strongly 

recommended that assembly is done on a soft, non-abrasive surface (such as the foam packing wrap) 

to avoid damaging the finish.

NOTES ON CARE AND MAINTENANCE:

Do not

 scratch or chip the finish.

- Inspect the product periodically, contact Delta Children's Products for replacement parts or questions.

Do not

 store the product or any parts in extreme temperatures and conditions such as a hot attic or a 

damp, cold basement. These extremes can cause a loss of structural integrity.

-To preserve the luster of the high quality finish on your product, it is recommended to place a doily or 

felt pad under any items you place on the finish.

-Clean with a damp cloth, then a dry cloth to preserve the original luster and beauty of this fine finish.  

-

Do not

 use abrasive chemicals.  

-

Do not

 spray cleaners directly onto furniture.

-Lift slightly when moving on carpeting to prevent leg breakage.

-Use of a vaporizer near furniture will cause wood to swell and finish to peel.

NOTES ON USE:

Keep children and others safe by following these simple rules:

Do not

 allow any child to play on furniture

Do not

 allow climbing on any piece of furniture.

Do no

t allow hanging from any piece of furniture.

- Always monitor your child’s activity when in the nursery.

Содержание Crib N Changer





























Отзывы: