Dell XPS /Dimension Скачать руководство пользователя страница 28

Страница: 28 / 49

Follow the instructions in "

Before You Begin

Open the computer cover

Remove any components that restrict access to the system board.

Disconnect all cables from the system board.

Before you remove the existing system board assembly, visually compare the replacement system board to the existing system board to make sure

that you have the correct part.

Remove the system board screw.

Pull up on the two tabs, slide the system board assembly toward the front of the computer, and then lift the assembly up and away.

Place the system board assembly that you just removed next to the replacement system board.

Replacing the System Board

Transfer components from the existing system board to the replacement system board:

Remove the memory modules

and install them on the replacement board.

Remove the heat-sink assembly and microprocessor

from the existing system board and transfer them to the replacement system board.

Configure the settings of the replacement system board.

Set the jumpers on the replacement system board so they are identical to the ones on the existing board.

Orient the replacement board by aligning the notches on the bottom of the board with the tabs on the computer.

Slide the system board assembly toward the back of the computer until the assembly clicks into position.

Replace any components and cables that you removed from the system board.Reconnect all cables to their connectors at the back of the computer.

Close the computer cover

Connect your computer and devices to electrical outlets, and turn them on.

NOTICE:

The system board and metal tray are connected and are removed as one piece.

CAUTION:

The microprocessor package and heat-sink assembly can get hot. To avoid burns, ensure that the package and assembly have had

sufficient time to cool before you touch them.

NOTE:

Some components and connectors on the replacement system board may be in different locations than the corresponding connectors on the

existing system board.

NOTICE:

To connect a network cable, first plug the cable into the network wall jack and then plug it into the computer.

Содержание XPS /Dimension


















































Результаты поиска

Содержание XPS /Dimension

Отзывы:

Похожие инструкции для XPS /Dimension

Бренды по названию

Популярные бренды

Dell XPS /Dimension, Руководство по обслуживанию

Результаты поиска

Содержание XPS /Dimension

Отзывы:

Похожие инструкции для XPS /Dimension

Бренды по названию

Популярные бренды