manualshive.com logo in svg

Dell W-IAP277, Руководство по установке, Страница: 4 / 16

Поделиться
Скачать
Dell W-IAP277 Скачать руководство пользователя страница 4

4

Dell Networking W-IAP277 Outdoor Instant Access Point

| Installation Guide

Table 2  

W-IAP277 LED Status during Operation

USB Console Port

The USB Micro-B console port allows you to connect the IAP to a terminal or a laptop for direct local 
management. Use the included USB console cable to connect the IAP. You can download the necessary driver for 
USB-UART adapter from 

download.dell-pcw.com

 

under the 

Tools & Resources

 tab.

Use the following setting to access the terminal:

Ethernet Ports

The W-IAP277 Instant access point is equipped with two 10/100/1000Base-T (RJ-45) Gigabit Ethernet ports 
(WAN and LAN port) for wired network connectivity. The WAN port supports 802.3at Power over Ethernet 
(PoE), accepting 48 VDC (nominal) as a standard defined Powered Device (PD) from a Power Sourcing 
Equipment (PSE) such as a PoE midspan injector.

These ports have RJ-45 female connectors with the pin-outs shown in 

Figure 3

.

Figure 3  

Gigabit Ethernet Port Pin-Out

Reset Button

The reset button can be used to return the IAP to factory default settings. To reset the IAP:

1. Power off the IAP.
2. Press and hold the reset button using a small, narrow object, such as a paperclip.
3. Power-on the IAP without releasing the reset button. The system LED will flash within 5 seconds.
4. Release the reset button.

The system LED will flash again within 15 seconds indicating that the reset is completed. The IAP will now 
continue to boot with the factory default settings.

AC Power Interface

The W-IAP277 Instant access point is capable of AC power in the range of 100 - 240 VAC. The power cord or 
power connector kit is sold separately.

LED

Color/State

Meaning

System LED

Solid Red

General fault

One blink every 3 seconds

Radio 0 fault (5 GHz)

Two quick blinks 0.5 seconds 

apart cycled every 3 seconds

Radio 1 fault (2.4GHz)

Table 3  

Console Settings

Baud Rate

Data Bits

Parity

Stop Bits

Flow Control

9600

8

None

1 None

1000Base-T Gigabit 

Ethernet Port

RJ-45 Female
Pin-Out

Signal Name

1
2
3
4
5
6
7
8

BI_DC+
BI_DC-

BI_DD+
BI_DD-

BI_DA+
BI_DA-
BI_DB+

BI_DB-

Function

Bi-directional pair +C, PoE Positive
Bi-directional pair -C, PoE Positive

Bi-directional pair +D, PoE Negative
Bi-directional pair -D, PoE Negative

Bi-directional pair +A, PoE Negative
Bi-directional pair -A, PoE Negative
Bi-directional pair +B, PoE Positive

Bi-directional pair -B, PoE Positive

Содержание W-IAP277

















Отзывы:

Нет отзывов