Dell Precision 3440 Small Form Factor Скачать руководство пользователя страница 63

Страница: 63 / 76

Option

Description

•

Weekdays

•

Select Days

Default setting: Disabled

Deep Sleep
Control

Allows you to aggressive the system is at conserving power while Shut down (S5) or in Hybernate (S4) mode.

•

Disabled

•

Enabled in S5 only

•

Enabled in S4 and S5 (default)

USB Wake
Support

Allows you to enable USB devices to wake the system from Standby.

•

Enable USB Wake Support

Default setting: The option is enabled..

Wake on LAN/
WLAN

Allows you to enable or disable the feature that powers on the computer from the Off state when triggered by a
LAN signal.

•

Disabled

: This option is enabled by default.

•

LAN Only

•

WLAN Only

•

LAN or WLAN

•

LAN with PXE Boot

Block Sleep

This option lets you block entering to sleep (S3 state) in operating system environment.

Block Sleep (S3 state)

Default setting: This option is disabled

POST Behavior screen options

Option

Description

Numlock LED

This option specifies whether the NumLock LED should be on when the system boots.

•

Enable Numlock LED: The option is enabled.

Keyboard Errors

This option option specifies whether the keyboard related errors are reported when it boots.

•

Enables Keyboard Error Detection: The option is enabled by default.

Fastboot

Allows you to speed up the boot process by bypassing some of the compatibility steps. The options are:

•

Minimal

•

Thorough

(default)

•

Auto

Extend BIOS
POST Time

This option created an additional pre-boot delay.

•

0 seconds (default)

•

5 seconds

•

10 seconds

Full Screen Logo

. This option displays full screen logo if your image match screen resolution. The option Enable Full Screen Logo is
not selected by default.

Warnings and
Errors

•

Prompt on Warnings and Errors

(default)

•

Continue on Warnings

•

Continue on Warnings and Errors

System setup

Содержание Precision 3440 Small Form Factor













































































Результаты поиска

Содержание Precision 3440 Small Form Factor

Отзывы:

Похожие инструкции для Precision 3440 Small Form Factor

Бренды по названию

Популярные бренды

Dell Precision 3440 Small Form Factor, Руководство по обслуживанию

Результаты поиска

Содержание Precision 3440 Small Form Factor

Отзывы:

Похожие инструкции для Precision 3440 Small Form Factor

Бренды по названию

Популярные бренды