manualshive.com logo in svg

Dell OptiPlex 7090 Tower, Руководство по обслуживанию, Страница: 94 / 104

Поделиться
Скачать
Dell OptiPlex 7090 Tower Скачать руководство пользователя страница 94

Table 15. System setup options—Pre-boot Behavior menu 

Pre-boot Behavior

Warning and Errors

Enable or disable the action to be done when a warning or error is encountered.

By default, the 

Prompt on Warnings and Errors

 option is enabled.

Fastboot

Enable to set the speed of the boot process.

By default, the 

Thorough

 option is enabled.

Extend BIOS POST Time

Set the BIOS POST time.

By default, the 

0 seconds

 option is enabled.

Table 16. System setup options—Virtualization menu 

Virtualization

Intel Virtualization Technology

Enable Intel Virtualization Technology
(VT)

Specify whether a Virtual Machine Monitor (VMM) can utilize the additional
hardware capabilities that are provided by Intel Virtualization Technology.

By default, the option is enabled.

VT for Direct I/O

Specify whether a Virtual Machine Monitor (VMM) can utilize the additional
hardware capabilities that are provided by Intel Virtualization Technology for
Direct I/O.

By default, the option is enabled.

Intel Trusted Execution Technology
(TXT)

Enable Intel Trusted Execution
Technology (TXT)

Specifies whether a measured Virtual Machine Monitor (MVMM) can utilize the
additional hardware capabilities that are provided by Intel Trusted Execution
Technology.

By default, the option is disabled.

Table 17. System setup options—Performance menu 

Performance

Multi Core Support

Active Cores

Enables to change the number of CPU cores available to the operating system.

By default, the 

All Cores

 options are enabled.

Intel SpeedStep

Enable Intel SpeedStep Technology

Enables the computer to dynamically adjust processor voltage and core
frequency, decreasing average power consumption and heat production.

By default, the option is enabled.

C-States Control

Enable C-State Control

Enable or disable additional processor sleep states.

By default, the option is enabled.

Intel Turbo Boost Technology

Enable Intel Turbo Boost Technology

Enable or disable Intel TurboBoost mode of the processor.

By default, the option is enabled.

Intel Hyper-Threading Technology

Enable Intel Hyper-Threading Technology Enable or disable Hyper-Threading in the processor.

By default, the option is enabled.

94

System setup

Содержание OptiPlex 7090 Tower









































































































Отзывы:

Нет отзывов