manualshive.com logo in svg

Dell OptiPlex 7090 Tower, Руководство по обслуживанию, Страница: 32 / 104

Поделиться
Скачать
Dell OptiPlex 7090 Tower Скачать руководство пользователя страница 32

Steps

1. Align the notch on the memory module with the tab on the memory-module slot.
2. Slide the memory module firmly into the slot at an angle and press the memory module down until it clicks into place.

NOTE:

 If you do not hear the click, remove the memory module and reinstall it.

Next steps

1. Install the 

side cover

.

2. Follow the procedure in 

after working inside your computer

.

Processor fan and heat-sink assembly

Removing the processor fan and 125 W heat-sink assembly

Prerequisites

1. Follow the procedure in 

before working inside your computer

.

WARNING:

 The heat sink may become hot during normal operation. Allow sufficient time for the heat sink to

cool before you touch it.

CAUTION:

 For maximum cooling of the processor, do not touch the heat transfer areas on the heat sink. The

oils in your skin can reduce the heat transfer capability of the thermal grease.

2. Remove the 

side cover

.

About this task

The following images indicate the location of the processor fan and 125 W heat-sink assembly and provide a visual
representation of the removal procedure.

32

Removing and installing components

Содержание OptiPlex 7090 Tower









































































































Отзывы:

Нет отзывов