Dell Inspiron 5521 Скачать руководство пользователя страница 49

Страница: 49 / 118

Next steps

1. Install the

2. Install the

3. Install the

4. Exit

5. Follow the procedure in

After working inside your computer

Removing the heat sink and fan assembly - Discrete configuration

Prerequisites

1. Follow the procedure in

Before working inside your computer

CAUTION:

For maximum cooling of the processor, do not touch the heat transfer areas on the heat sink. The

oils in your skin can reduce the heat transfer capability of the thermal grease.

NOTE:

The heat sink may become hot during normal operation. Allow sufficient time for the heat sink to cool before you

touch it.

2. Enter

3. Remove the

4. Remove the

5. Remove the

About this task

The following images indicate the location of the heat sink and fan assembly for a system with discrete configuration and
provide a visual representation of the removal procedure.

Removing and installing components

Содержание Inspiron 5521























































































































Результаты поиска

Содержание Inspiron 5521

Отзывы:

Бренды по названию

Популярные бренды

Dell Inspiron 5521, Руководство по обслуживанию

Результаты поиска

Содержание Inspiron 5521

Отзывы:

Бренды по названию

Популярные бренды