Dell Inspiron 5521 Скачать руководство пользователя страница 102

Страница: 102 / 118

Table 7. System setup options—Storage menu (continued)

Storage

Enable MediaCard

Secure Digital (SD) Card

Enable or disable the SD card.

By default, the

Secure Digital (SD) Card

option is enabled.

Secure Digital (SD) Card Read-Only Mode Enable or disable the SD card read-only mode.

By default, the

Secure Digital (SD) Card Read-Only Mode

option is not

enabled.

Table 8. System setup options—Display menu

Display

Display Brightness

Brightness on battery power

Enable to set screen brightness when the computer is running on battery
power.

Brightness on AC power

Enable to set screen brightness when the computer is running on AC power.

Touchscreen

Enable to activate the Touchscreen on operating system

Full Screen Logo

Enable or disable full screen logo.

By default, the option is not enabled.

Table 9. System setup options—Connection menu

Connection

Network Controller Configuration

Integrated NIC

Controls the on-board LAN controller.

By default, the

Enabled with PXE

option is enabled.

Enable UEFI Network Stack

Enable or disable UEFI Network Stack.

By default, the

Enable UEFI Network Stack

and

Enabled w/PXE

option are

enabled.

Wireless Device Enable

WWAN/GPS

Enable or disable the internal WWAN/GPS device

By default, the option enabled.

WWAN Bus Mode

Set the interface type of the Wireless Wan (WWAN) card.

By default, the

Bus Mode PCIe

option is enabled.

WLAN

Enable or disable the internal WLAN device

By default, the option enabled.

Bluetooth

Enable or disable the internal Bluetooth device

By default, the option enabled.

Contactless smartcard/NFC

Enable or disable the internal Contactless smartcard/NFC device

By default, the option enabled.

Enable UEFI Network Stack

Enable or disable UEFI Network Stack and controls the on-board LAN
Controller.

By default, the

Enable UEFI Network Stack

option are enabled.

Wireless Radio Control

102

System setup

Содержание Inspiron 5521























































































































Результаты поиска

Содержание Inspiron 5521

Отзывы:

Бренды по названию

Популярные бренды

Dell Inspiron 5521, Руководство по обслуживанию

Результаты поиска

Содержание Inspiron 5521

Отзывы:

Бренды по названию

Популярные бренды