Dell FS7500 Скачать руководство пользователя

Страница: 41 / 88

EqualLogic FS7500 Installation and Setup

3 Power Connections

2. Use a power cable with a C13 connector and a C14 connector to connect the controller’s left power supply

to the output receptacle on the same BPS power module to which you connected the USB cable in the
previous step (see callout 2 in

Figure 31

). Use the cable strain relief strap on the power supply to secure the

power cable to the controller chassis.

3. Using a power cable with a C13 connector and a connector that fits the receptacle of your power source,

connect the controller’s right power supply to a power source (callout 3 in

Figure 31

). Use the cable strain

relief strap on the power supply to secure the power cable to the controller chassis.

For high availability, make sure the power source is not the same as the power source to which the BPS
power module is connected.

4. Repeat the three steps to connect the second controller to the other power module on the BPS.

Removing the Controller Bezel

To remove the FS7500 Controller bezel, see

Figure 32

and follow these steps:

1. Use the key to unlock the bezel, if it is locked (callout 3).

2. Push up on the release latch on the left side of the bezel and carefully pull out the bezel from the left side of

the controller (callout 2).

3. Holding the bezel, move it to the left to disengage the bezel from the right side of the controller (callout 1).

Figure 32: Removing the Controller Bezel

Содержание FS7500

























































































Результаты поиска

Содержание FS7500

Отзывы:

Похожие инструкции для FS7500

Бренды по названию

Популярные бренды

Dell FS7500, Установка и настройка

Результаты поиска

Содержание FS7500

Отзывы:

Похожие инструкции для FS7500

Бренды по названию

Популярные бренды