Dell FS7500 Скачать руководство пользователя

Страница: 40 / 88

4. Turn on the controller and make sure the controller is operational. See

Turning On Power to a Controller on

page 36

5. Attach the controller bezel. See

Attaching the Controller Bezel on page 26

The following sections describe these steps in detail.

Figure 31

shows the two controllers and the BPS properly

connected.

Figure 31: Complete EqualLogic FS7500Power Connections

Table 11: EqualLogic FS7500 Power Connections

Callout

Description

USB connection from Controller 1 to BPS power module 1

Power connection from Controller 1 to BPS power module 1

Power connection from Controller 1 to Power Source 1

USB connection from Controller 2 to BPS power module 2

Power connection from Controller 2 to BPS power module 2

Power connection from Controller 2 to Power Source 2

Power connection from BPS to Power Source 2

Power connection from BPS to Power Source 1

Connecting a Controller to a Power Source and a BPS Power Module

To connect a controller to a power source and a BPS power module, see

Figure 31

and

Table 11

and follow

these steps:

1. Connect the A connector on the USB cable to the USB port on the controller (located to the left of the

bottom network interface card) and connect the B connector to the USB port on a BPS power module
(callout 1 in

Figure 31

EqualLogic FS7500 Installation and Setup

3 Power Connections

Содержание FS7500

























































































Результаты поиска

Содержание FS7500

Отзывы:

Похожие инструкции для FS7500

Бренды по названию

Популярные бренды

Dell FS7500, Установка и настройка

Результаты поиска

Содержание FS7500

Отзывы:

Похожие инструкции для FS7500

Бренды по названию

Популярные бренды