Dell Alienware m17 R2 Скачать руководство пользователя страница 17

Страница: 17 / 70

About this task

NOTE: This procedure applies only to computers shipped with a M.2 2280 solid-state drive installed.

NOTE: Depending on the configuration ordered your computer may have up to two M.2 cards installed. Supported card
configurations per M.2 card slot:

• M.2 2230 solid-state drive + 2230 mounting bracket
• M.2 2280 solid-state drive

The following image indicates the location of the M.2 2280 solid-state drive and provides a visual representation of the removal

procedure.

Steps
1. Remove the screw (M2x3) that secures the M.2 thermal shield to the palm-rest assembly.
2. Lift and remove the M.2 2280 thermal shield off the M.2 2280 solid-state drive.

NOTE: A thermal shield is only present on PCIe M.2 cards.

3. Slide and remove the M.2 2280 solid-state drive from the M.2 card slot on the system board.

Installing the M.2 2280 solid-state drive

Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

NOTE: This procedure applies if you are installing a M.2 2280 solid-state drive.

NOTE: Depending on the configuration ordered your computer may have up to two M.2 cards installed. Supported card
configurations per M.2 card slot:

• M.2 2230 solid-state drive + 2230 mounting bracket
• M.2 2280 solid-state drive

Содержание Alienware m17 R2







































































Результаты поиска

Содержание Alienware m17 R2

Отзывы:

Похожие инструкции для Alienware m17 R2

Бренды по названию

Популярные бренды

Dell Alienware m17 R2, Руководство по обслуживанию

Результаты поиска

Содержание Alienware m17 R2

Отзывы:

Похожие инструкции для Alienware m17 R2

Бренды по названию

Популярные бренды