background image

Back to Contents Page

  

 

 System Board  

Dell™ Inspiron™ 1545 Service Manual 

 

  

Removing the System Board 

 

  

Replacing the System Board 

 

 

 

 

The system board's BIOS chip contains the Service Tag, which is also visible on a barcode label on the bottom of the computer. The replacement kit for the 
system board includes a CD that provides a utility for transferring the Service Tag to the replacement system board. 

 

Removing the System Board  

 

 

1.

Follow the instructions in 

Before You Begin

.  

 

 

  

2.

Remove the hard drive (see 

Removing the Hard Drive

).  

 

 

  

3.

Remove the optical drive (see 

Removing the Optical Drive

).  

 

 

  

4.

Remove the center control cover (see 

Removing the Center Control Cover

).  

 

 

  

5.

Remove the keyboard (see 

Removing the Keyboard

).  

 

 

  

6.

Remove the base cover (see 

Removing the Base Cover

).  

 

 

  

7.

Remove any installed memory modules (see 

Removing the Memory Module(s)

).  

 

 

  

8.

Remove the processor heat sink and processor (see 

Removing the Processor Heat Sink

 and 

Removing the Processor

).  

 

 

  

9.

Remove the display assembly (see 

Removing the Display Assembly

).  

 

 

  

10.

Remove the palm rest (see 

Removing the Palm Rest

).  

 

 

  

11.

Remove the daughter board (see 

Removing the Daughter Board

).  

 

 

  

12.

Remove the four screws that secure the system board to the computer base.  
 

  

 

CAUTION: 

Before working inside your computer, read the safety information that shipped with your computer. For additional safety best 

practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.

 

NOTICE: 

To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such 

as the back panel) on the computer.

 

NOTICE: 

To help prevent damage to the system board, remove the main battery (see 

Before Working Inside Your Computer

) before working inside the 

computer.

 

NOTICE: 

Only a certified service technician should perform repairs on your computer. Damage due to servicing that is not authorized by Dell™ is not 

covered by your warranty.

 

NOTICE: 

Handle components and cards by their edges, and avoid touching pins and contacts.

1  thermal fan cable connector  2  USB extend cable connector 

Содержание 1545 - Inspiron - Pentium 2 GHz




















































Отзывы: