Dell 13 7000 2-in-1 Скачать руководство пользователя страница 85

Страница: 85 / 95

Power Management

USB Wake Support

Enable the USB devices to wake the computer from
Standby.

Wake on LAN

Enable the LAN signal to wake the computer from
the off state or hibernation.

NOTE: This feature only works when the
computer is connected to AC.

Advanced Battery Charge
Configuration

Enable Advanced Battery Charge Configuration

from the beginning of the day to a specified work
period.

Primary Battery Charge
Configuration

Set the primary battery charge settings with a
preselected custom charge start and stop.
Default: Adaptive.

Table 11. System setup options—POST Behavior menu

POST Behavior

Adapter Warnings

Enable adapter warnings.
Default: Enabled.

Fn Lock Options

Enable or disable the Fn lock mode.

Fastboot

Enable to set the speed of the boot process.
Default: Thorough.

Extended BIOS POST Time Creates an additional pre-boot delay.

Full Screen Logo

Enable to display full screen logo.

Warnings and Errors

Specify whether the boot process will continue or
prompt for user input when warnings and errors are
detected.

NOTE: Critical errors will always halt the
system.

Содержание 13 7000 2-in-1
































































































Результаты поиска

Содержание 13 7000 2-in-1

Отзывы:

Похожие инструкции для 13 7000 2-in-1

Бренды по названию

Популярные бренды

Dell 13 7000 2-in-1, Руководство по обслуживанию

Результаты поиска

Содержание 13 7000 2-in-1

Отзывы:

Похожие инструкции для 13 7000 2-in-1

Бренды по названию

Популярные бренды