Dell EMC PowerEdge MX5000s Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 43

background image

Installing an expander module

Prerequisites

1. Follow the safety guidelines listed in

Safety instructions

on page 14.

2.

Open the drive drawer.

Steps

1. Align the expander card to the connector slot.
2. Press the expander card lever down until it firmly seats into the expander slot.

Figure 21. Installing an expander module

Next steps

1. Ensure that the expander modules have the same firmware version. If there is a firmware mismatch, the LED indicator flashes an error

sequence. For more information about the Expander LED health indicators, see

Expander health status indicators

on page 38.

2.

Close the drive drawer.

SAS IOM module

Removing a MX5016s blank from Fabric C slot

Steps

1. Press the release button to release the blank.
2. Pull the blank out of the enclosure.

NOTE:

To maintain proper airflow, ensure that the blanks are installed if the MX5016s is not installed.

Installing and removing system components

27

«
...
25
26
27
28
29
...
»

Содержание PowerEdge MX5000s












































Отзывы:

Нет отзывов

Похожие инструкции для PowerEdge MX5000s

Бренд: IEI Technology Страницы: 9

Бренд: Supermicro Страницы: 58

Бренд: Nortel Страницы: 4

Бренд: Optimus Страницы: 36

FCM-CHS2 Series

Бренд: AAxeon Страницы: 16

Бренд: Lumens Страницы: 2

Бренд: Viglen Страницы: 58

MS901K-AP Series

Бренд: TCL Страницы: 59

iConverter XM5 8261-0

Бренд: Omnitron Systems Страницы: 2

Бренд: Leckey Страницы: 47

Chassis RM21400

Бренд: Chenbro Страницы: 17

Бренд: Chenbro Страницы: 20

SR301 Plus series

Бренд: Chenbro Страницы: 29

SR107 Plus Series

Бренд: Chenbro Страницы: 34

Бренд: Chenbro Страницы: 46

Бренд: Chenbro Страницы: 55

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды