Dell EMC PowerEdge MX5000s Скачать руководство пользователя

Страница: 38 / 43

Expander health status indicators

Expander health status indicator indicates the health condition of the expander module and identification indicator helps to locate a
particular expander card within the storage sled.

Figure 27. Expander health indicators

Table 17. Expander health status indicators

Indicator,

Button, or

Connector

Icon

Description

Condition

Identification
indicator

Flashes blue for one second and then turns off.

NOTE:

LED is OFF, when no

Identification in progress.

Identify

Diagnostic
indicator

Green

Expander card in good health

Flashes amber for two seconds and turns off.

Expander card failure

Flashes continuous green for 5 times and then
turns off for two seconds.

Expander firmware mismatch

System diagnostics and indicator codes

Содержание PowerEdge MX5000s












































Результаты поиска

Содержание PowerEdge MX5000s

Отзывы:

Похожие инструкции для PowerEdge MX5000s

Бренды по названию

Популярные бренды

Dell EMC PowerEdge MX5000s, Инструкция по установке и обслуживанию

Результаты поиска

Содержание PowerEdge MX5000s

Отзывы:

Похожие инструкции для PowerEdge MX5000s

Бренды по названию

Популярные бренды