manualshive.com logo in svg

Delem DA-52, Справочное руководство, Страница: 38 / 48

Поделиться
Скачать
Delem DA-52 Скачать руководство пользователя страница 38

V0608, 5.2

Material  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

MA

Selection of one of the programmed materials, which are used to calculate the bending 
depths. The control contains 4 preprogrammed materials. In total, 6 materials can be 
programmed on the control. See the chapter about programming constants how to 
program materials.

Thickness  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

TH

Thickness of the sheet.

Length  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

BL

Length of the sheet between the tools.

Method . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

BM

Select the required bending method. The control supports 4 methods:
Air bend
Bottoming
See chapter 2 for more information about possible bend methods.

Corr. 

α

 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

C

α

Correction on angle to bend
The angle correction should be entered as follows:
- Programmed value of 90 degrees.
- Measured value of 92 degrees.
Then it is required to program Corr._ with -2.
- Programmed value of 90 degrees.
- Measured value of 88 degrees.
Then it is required to program Corr._ with +2.

Angle  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

α

Angle to bend.

Y1-axis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Y

The programmed or calculated Y-axis value to realise a certain angle.

Y2-axis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Y

The programmed or calculated Y-axis value to realise a certain angle. Normally Y2 is 
copied from Y1. Y2 can be programmed differently in case of conical bending.

Mute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

M

Sequence point where the Y-axis is switched from fast closing speed to pressing speed. 
It is programmed here as a Y-axis position value.

Содержание DA-52

















































Отзывы:

Нет отзывов