manualshive.com logo in svg

DEK The Beast 100TB, Руководство пользователя

Поделиться
Скачать
DEK The Beast 100TB Скачать руководство пользователя страница 25

100TB 

THE BEAST 

 

 

Rev: Mar2011 

THE BEAST  

Tow Behind Mower 

21 

Troubleshooting 

Problem Possible 

Causes  Solution 

Engine will not start 

1.  Key in the OFF position 
2.  Insufficient fuel in the tank 
3.  Air bubble in the fuel line 
4.  Fuel valve in OFF position 
5.  Choke not ON 
6.  Choke linkage out of adjustment 
7.  Low engine oil 
8.  Blade control in ON position 
9.  Loose spark plug wire  
10.  Fouled spark plug  
11.  Plugged or dirty air filter  
12. Bad gasoline 
13.  Plugged or dirty fuel filter  

14.  Safety switches out of 

alignment or loose 

15.  Dead battery (electric start 

models) 

 

1.  Turn key to ON position 
2. Add 

gasoline 

3.  Prime engine or shake bubble out 
4.  Turn valve ON 
5. Turn 

choke 

ON 

6.  Refer to Engine Owner’s Manual 
7. Add 

engine 

oil 

8.  Push lever to OFF position 
9.  Tighten wire or connections 
10.  Clean or replace the plug 
11.  Clean or replace the air filter 
12.  Drain and replace the gasoline 
13.  Replace the fuel filter 
14.  Adjust or tighten switches (p. 17) - read warnings! 

 

15.  Recharge or replace battery 

 

To test whether the blade activation safety switches 
are a contributing factor to the engine not starting, 
depress the Operator Presence Switch on the handle 
bars while trying to start the engine. If engine starts, a 
safety switch adjustment is required. 

 

Engine will not keep 
running/quits 

1.  Water in the fuel 

2. Loose 

safety 

switch 

3.  Fuel valve is OFF 
4. Dirty 

fuel 

filter 

5.  Dirty air filter 
6.  Low engine oil 

 

1.  Drain and replace fuel 
2.  Adjust switch (p. 17) 
3.  Turn fuel valve ON 
4.  Replace fuel filter 
5.  Clean or replace air filter 
6. Add 

engine 

oil 

Engine stops when blades 
are engaged 

1. Loose 

safety 

switch 

2.  Belt tension too high 
3.  Blades jammed with foreign 

material 

 

1.  Adjust switch (p. 17) 
2.  Adjust belt (p. 19) 
3.  Remove foreign material 

 

Note: Firmly pushing the blade control lever into the 
OFF position to ensure the safety switch is fully 
engaged can sometimes resolve this problem. 

 

Blades do not turn 

1.  Broken belt 
2. Loose 

belt 

3.  Blade activation linkage out of 

adjustment. 

 

1. Replace 

belt 

2.  Adjust belt (p. 19) 
3.  Adjust linkage (p. 13) 

Belts squeal when blades 
are engaged 

1.  Incorrect belt tension 
2.  Excessive belt wear 

 

1.  Adjust belt tension 
2. Replace 

belt 

Belts slip when blades are 
engaged 

1.  Incorrect belt tension 
2.  Excessive belt wear 

 

1.  Adjust belt tension 
2. Replace 

belt 

Содержание The Beast 100TB




























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды