DEK The Beast 100TB Скачать руководство пользователя страница 14

100TB 

THE BEAST 

 

 

Rev: Mar2011 

THE BEAST  

Tow Behind Mower 

10 

Mowing in Reverse  

1.  ALWAYS watch where you are going, and make 

certain the area is clear before backing up. 
 

2.  Back up slowly and carefully. Do not allow THE 

BEAST to jackknife.   
 

3.  If the hitch is in an offset configuration, use 

EXTREME CAUTION in reverse to prevent jack-
knifing.   

 

NEVER BACK THE MOWER TOWARDS DITCHES OR 
OVER RIDGES ONTO SLOPES. THE WEIGHT OF THE 
MOWER CAN PULL YOU AND YOUR TOWING VEHICLE 
INTO A DITCH OR DOWN A HILL CAUSING SERIOUS 
INJURY OR DEATH. 
 

Executing Turns with THE BEAST 

1.  ALWAYS reduce speed to make turns of any kind. 
2.  The turning radius of THE BEAST is limited by the 

design of the towing vehicle. The hitch can come 
into contact with the towing vehicle during turns, 
and the radius of the turn must be limited to prevent 
this contact. 

3.  Use EXTREME CAUTION when executing turns on 

hills and slopes. 

4.  Tow behind models equipped with wing mowers 

can potentially execute a zero turn about the tip of 
one of the wings. Use EXTREME CAUTION due to 
the potential to jack-knife THE BEAST. 

 

Operating Instructions 

 

Starting the Engine 

 

 

 

DANGER! Exhaust contains poisonous carbon 
monoxide, a colorless and odorless gas. Breathing 
exhaust can cause loss of consciousness and may 
lead to death. Do not operate the engine in a 
confined space where dangerous carbon monoxide 
fumes can collect. 

 

NOTE: Be sure to add fresh unleaded gasoline and fill 
the engine with manufacturers recommended motor oil 
before starting your mower.

  

 

1.  Make sure the shut off 

valve, located at the 
bottom of the tank, is in 
the ON position.  
 

2.  Make sure the blade 

control lever is in the OFF position. NOTE: The 
safety interlock system prevents the engine from 
being started if the blade control lever is not in the 
OFF position. 

3.  Pull CHOKE if necessary. 
4.  Turn the key clockwise to the START position and 

allow it to return to the ON position when the 
engine starts. 

5.  When the engine starts to run and the key returns 

to the ON position, push CHOKE off. 

 

Stopping the Mower 

To stop THE BEAST, turn the remote toggle switch to 
the OFF position or turn the mower off at the main 
control panel on the back corner of the chassis. Make 
certain the blades are turned to the OFF position before 
attempting the restart. Note: The key must be in the OFF 
position, even if the remote shut-down switch is on OFF, 
to prevent drain on the battery. 

 

Braking distances for the towing vehicle will be 
increased because of the weight of the Tow Behind 
Mower. Use caution until you are comfortable with the 
abilities of the towing vehicle to stop the mower. 

Before attempting to use THE BEAST, make sure 
you are familiar with all of the components and 
have read the manual. 

DANGER 

Содержание The Beast 100TB




























Отзывы: