manualshive.com logo in svg

DEI PCX-7500, Руководство по эксплуатации

Поделиться
Скачать
DEI PCX-7500 Скачать руководство пользователя страница 14

 

Sync Output 

Synchronization pulses for external devices are available at the Sync Output BNC 
connector. The sync pulse corresponds to the leading edge of the output current 
pulse. 
 

Keyswitch 

The keyswitch ON position allows the PCX-7500 output current to be enabled.  In 
the keyswitch OFF position, the PCX-7500 is disabled. 

 

™

 

Rear Panel Features 

 

 

 

 

 

 

 

Current Output 

This socket accepts the factory-supplied output cable and is the connection for the 
system-generated current pulses. DO NOT TOUCH any part of this cable while the 
PCX-7500 is powered up. Please review the Safety section. 
 

Note:

  The absence of a properly installed output cable disables the output and 

creates an output enable fault. 
 

Rear Enable 

This connector accepts either an external dry contact closure or the factory-supplied 
shorting BNC plug. Closed contacts or the use of the shorting plug enables the 
output. Open contacts or removal of the shorting plug disables the output and 
creates a rear enable fault. 

USB

 

Ethernet

 

RS232

 

AC

 

Power

 

Connector

 

Current

 

Output

 

Power

 

Switch

 

Rear

 

Enable

 

Voltage

 

Monitor

 

Содержание PCX-7500





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды