16 / EN
Washing Machine / User’s Manual
Changing the auxiliary function, speed and
temperature
Depending on the step the programme has reached, you
can cancel or activate the auxiliary functions. See, "Auxiliary
function selection".
You can also change the speed and temperature settings.
See, "Spin speed selection" and "Temperature selection".
C
The loading door will not open if the water temperature
in the machine is high or the water level is above the
door opening.
4.12 Child Lock
Use Child Lock function to prevent children from tampering
with the machine. Thus you can avoid any changes in a
running programme.
C
You can switch on and off the machine with
On / Off
button when the Child Lock is active. When you switch
on the machine again, programme will resume from
where it has stopped.
When the child lock is enabled, an audio warning will
be given if the buttons are pressed. Audio warning
will be canceled if the buttons are pressed 5 times
consecutively.
To activate the Child Lock:
Press and hold Auxiliary Function
button 2 for 3
seconds. After the countdown as “CL 3-2-1" on the display
is over, "Child Lock Enabled" appears on the display. Release
2nd Auxiliary Function button 1
when this warning is
displayed.
To deactivate the childproof lock:
Press and hold Auxiliary Function
button 2 for 3
seconds. After the countdown as
“CL 3-2-1”
on the display
is over, "Child Lock Enabled" disappears from the display.
4.13 Canceling the programme
The programme is cancelled when the machine is turned off
and on again. Press and hold
On / Off
button for 3 seconds.
After the countdown as "3-2-1" on the display is over, the
machine turns off.
C
If you press
On / Off
button when the Child Lock is
enabled, the programme will not be cancelled. You must
cancel the Child Lock first.
If you want to open the loading door after you have
cancelled the programme but it is not possible to open
the loading door since the water level in the machine
is above the loading door opening, then turn the
Programme Selection
knob to
Pump+Spin
programme and discharge the water in the machine.
4.14 End of programme
End symbol appears on the display when the programme is
completed.
If you do not press any button for 10 minutes, the machine
will switch to OFF mode. Display and all indicators are turned
off.
Completed programme steps will be displayed if you press
On / Off button.
5 Maintenance and cleaning
Service life of the machine extends and frequently faced
problems decrease if cleaned at regular intervals.
5.1 Cleaning the detergent drawer
Clean the detergent drawer at regular intervals (every
4-5 washing cycles) as shown below in order to prevent
accumulation of powder detergent in time.
Lift the rear part of the siphon to remove it as illustrated.
C
If more than normal amount of water and softener
mixture starts to gather in the softener compartment,
clean the siphon.
2 Wash the detergent drawer and the siphon with plenty of
lukewarm water in a washbasin. Wear protective gloves
or use an appropriate brush to avoid touching of the
residues in the drawer with your skin when cleaning.
3 After cleaning, replace the siphon back to its seating and
push its front section downwards to make sure that the
locking tab engages.
5.2 Cleaning the loading door and the drum
Residues of softener, detergent and dirt may accumulate in
your machine in time and may cause unpleasant odours and
washing complaints. To avoid this, use the
Drum Cleaning
programme. If your machine is not featured with
Drum
Cleaning
programme, use
Cottons-90
programme and
select
Additional water
or
Extra Rinse
auxiliary functions
as well. Run the programme without any laundry in the
machine. Before starting the programme, put max. 100
g of powder anti-limescale into the main wash detergent
compartment(compartment nr. 2). If the anti-limescale is in
tablet form, put only one tablet into compartment nr. 2. Dry
the inside of the bellow with a clean piece of cloth after the
programme has come to an end.
C
Repeat Drum Cleaning process in every 2 months.
Use an anti-limescale suitable for the washing
machines.
4.15 Adjusting the VOLUME level
Low volume and high volume
Press and hold Auxiliary Function button 3 for 3 seconds to
adjust the volume level. After the countdown as "3-2-1" on
the display is over, the volume level symbol will appear and
the new volume level will be displayed.
Содержание WMY 81443 MLCM
Страница 1: ...2820524090 19 06 14 10 02 Document Number WMY 81443 MLCM ...
Страница 26: ......
Страница 27: ......