DeDietrich KALIKO Essentie ETWH 180 E Скачать руководство пользователя страница 9

Страница: 9 / 60

1.3

Specific safety instructions

Warning

In accordance with the NFC 15.100 electrical

safety standard, only qualified professionals are

permitted access to the inside of the appliance.

Warning

Ensure correct earthing.

Heating water and domestic water must not

come into contact with each other.

A disconnection device must be fitted to

permanent pipes in accordance with installation

rules.

If the power cable is damaged, it must be

replaced by the manufacturer, its after sales

service or persons with similar qualifications in

order to obviate any danger.

This appliance must not be powered through an

external switch, such as a timer, or be

connected to a circuit which is regularly

switched on and off by the electricity provider.

Install the appliance in accordance with national

rules on electrical installation.

Wiring diagram: See chapter on Electrical

Principle Diagram.

Connecting the appliance to the mains: See

chapter on Electrical Connections.

Fuse type et calibre: See chapter on Electrical

Connections.

Regarding information on installation on the

appliance, electrical connection and connection

of the water circuit, refer to the paragraphs

below in this manual.

Regarding information on handling, servicing

and scrapping the appliance, refer to the

paragraphs below in this manual.

Caution

In order to limit the risk of being scalded, the

installation of a thermostatic mixing valve on the

domestic hot water flow pipes is recommended.

1 Safety

7629886 - v07 - 20072020

ETWH

Содержание KALIKO Essentie ETWH 180 E





























































Результаты поиска

Содержание KALIKO Essentie ETWH 180 E

Отзывы:

Похожие инструкции для KALIKO Essentie ETWH 180 E

Бренды по названию

Популярные бренды

DeDietrich KALIKO Essentie ETWH 180 E, Инструкция по установке и обслуживанию

Результаты поиска

Содержание KALIKO Essentie ETWH 180 E

Отзывы:

Похожие инструкции для KALIKO Essentie ETWH 180 E

Бренды по названию

Популярные бренды