decrane aerospace lcd-9084-301-x Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 19

decrane aerospace lcd-9084-301-x Скачать руководство пользователя страница 9

DeCrane Aerospace Audio International

LCD-9084-301-x Installation Manual

Document # 540332, Rev A, 01/2009

Page 8 of 18

3.4.3 Video Lines

Composite video connections shall be shielded coaxial cable in

accordance with

M17/94-RG179

or equivalent. Cable shields shall

be grounded at the source. Use of individual wires rather than

proper coaxial cable connections through production breaks is

unacceptable, and will cause significant and detrimental noise

introduction to the video signal supplied to the LCD-9084-301-x.

Serial digital video connections are recommended to use shielded

coaxial cable in accordance with

PIC V76261

or equivalent.

3.4.4 RS-485 Connections

RS-485 connections shall be twisted shielded cable with the shield

properly grounded at the source (ideal practice) and floating at the

load end. If shield cannot be grounded at the source, then ground

at the load end with the source end floating. Each wire length shall

be terminated at one end only. The shield for RS-485 shall be

terminated to a dedicated pin. Twisted shielded cable shall be in

accordance with

NEMA WC 27500

or equivalent.

3.4.5 RGB Connections

RGB wiring shall be in accordance with

NEMA WC 27500

or

equivalent.

«
...
7
8
9
10
11
...
»

Содержание lcd-9084-301-x




















Отзывы:

Нет отзывов