decaWave DW1000 Скачать руководство пользователя страница 73 | Manualshive

Страница: 73 / 242

background image

DW1000 User Manual

© Decawave Ltd 2017

Version 2.12

Page 73 of 242

Field

Description of fields within Register file: 0x04 – System Configuration

RXM110K

reg:04:00

bit:22

Receiver Mode 110 kbps data rate. This configuration when set to 1 will cause the receiver
to look for long SFD and process the PHY Header and RX data as per the 110 kbps frame
mode. When this configuration is 0, (the default), the receiver will look for short SFD and
will determine the RX data rate from the PHY header as either 850 kbps or 6.8 Mbps.

-

reg:04:00

bits:27–23

These bits are reserved and should always be set to zero to avoid any malfunction of the
device.

RXWTOE

reg:04:00

bit:28

Receive Wait Timeout Enable. When set RX Enable will initialise an RX_FWTO down count
which will disable the receiver if no valid frame is received before the timeout occurs. The
timeout period is set in

Register file: 0x0C – Receive Frame Wait Timeout Period

. The

occurrence of the timeout is signalled by the RXRFTO event status bit in

Register file: 0x0F –

System Event Status Register

RXAUTR

reg:04:00

bit:29

Receiver Auto-Re-enable.  This bit is used to cause the receiver to re-enable automatically.
Its operation changes depending on whether the IC is operating in single or double buffered
modes.  The default value is 0. With this setting, the IC will not automatically re-enable the
receiver  but  will  stop  receiving  and  return  to  idle  mode  whenever  any  receive  events
happen.  This includes receiving a frame but also failing to receive a frame because of some
error condition, for example an error in the PHY  header (as  reported by the  RXPHE event
status  bit  in

Register file: 0x0F – System Event Status Register

). In such cases if the host

wants to re-enable the receiver it must do it explicitly, using the RXENAB bit in

Register file:

0x0D – System Control Register

. The operation when RXAUTR = 1 is as follows:

(a) Double-buffered mode: After a frame reception event or failure (except a frame

wait timeout), the receiver will re-enable to receive another frame.

(b) Single-buffered mode: After a frame reception failure (except a frame wait

timeout), the receiver will re-enable to re-attempt reception.

For more information on frame reception see section 4

– Message Reception

Note:    In  double-buffered  mode  when  automatic  frame  acknowledgement  is  enabled  (by
the  AUTOACK  bit  below)  the  receiver  will  be  re-enabled  after  the  ACK  frame  has  been
transmitted.

AUTOACK

reg:04:00

bit:30

Automatic Acknowledgement Enable. Default value 0. This is the enable for the Automatic
Acknowledgement function. See section

5.3– Automatic Acknowledgement

for details of

operation of Automatic Acknowledgement.

AACKPEND

reg:04:00

bit:31

Automatic Acknowledgement Pending bit control. Default value 0. The value of the
AACKPEND bit is copied into the

Frame Pending

bit in the

Frame Control

field of the

DW1000 automatically generated ACK frame. See section

5.2 – Frame filtering

for details of

operation of frame filtering.

7.2.7 Register file: 0x05

– Reserved

ID

Length

(octets)

Type

Mnemonic

Description

0x05

-

-

-

Reserved – this register file is reserved

register file 0x05 is reserved for future use. Please take care not to write to this register as

doing so may cause the DW1000 to malfunction.

«
...
71
72
73
74
75
...
»

Содержание DW1000



















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DW1000

Бренд: Icom Страницы: 5

Бренд: halstrup-walcher Страницы: 34

Бренд: Harris Страницы: 148

Бренд: Harman Kardon Страницы: 4

Бренд: Harris Страницы: 4

Бренд: Javad Страницы: 10

Бренд: Javad Страницы: 7

Бренд: Javad Страницы: 4

Бренд: u-blox Страницы: 2

Бренд: Icom Страницы: 3

Бренд: La Crosse Technology Страницы: 2

Pocket Receiver 912T

Бренд: ASCOM Страницы: 2

Бренд: Omega Страницы: 32

Бренд: Rockville Страницы: 16

Бренд: AMG Страницы: 12

Бренд: Listen Страницы: 2

Vision BT-WR02 RF

Бренд: Watts Страницы: 20

Бренд: M-system Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды