If you want to construct your own data cables, be sture to use standard two conductor shielded cable (this
cable may be purchased at almost all professional sound and lighting stores). Your cables should be made
with a 3-pin male and female XLR connector on either end of the cable. Also remember that DMX lines must
be daisy chained and can not be split.
Be sure to follow the figures 2 and 3 below when making your own cables. Do not use the ground lug on the
XLR connector. Do not connect the cable’s shield conductor to the ground lug or allow the shield conductor
to come in contact with the XLR’s out casing. Grounding the shield could case a short circuit and erratic
behavior.
Special note: Line termination
When longer runs of cable are used, you may need to use a terminator on the last unit to avoid erratic
behavior. A terminator is a 120 Ohm 1/4W resistor which is connected to pins 2 and 3 of a male XLR connector
(DATA+ and DATA-). This unit is inserted in the female XLR connector of the last unit in your daisy chain to
terminate the line. Using a cable terminator will decrease the possibilities of erratic behavior.
5-pin XLR DMX connectors
Some manufacturers use 5-pin XLR connector for DATA transmission in place of 3-pin. 5-pin XLR fixtures may be
implemented in a 3-pin XLR DMX line. When inserting standard 5-pin XLR connectors in to a 3-pin line a cable
adaptor must be used, these adaptors are readily available at most electric stores. The chart below details a
proper cable conversion:
Controls and functions
Rear panel layout
Power input: AC100~120V (3.2A) / AC220~240V (1.2A), 50~60Hz
1.
Voltage selector: AC120V/230V optional by this voltage selector
2.
2.Main Features
3.Set Up
3.1 Power Supply:
Before plugging your unit in, be sure the source voltage in your area matches the required voltage for your
High Power DMX Controller TV
power supply. The
High Power DMX Controller TV
is available in a 120v and
230v version. Due to variations in line voltage from venue to venue, be sure to plug your power supply into a
wall outlet with matching power before attempting to operate.
Notice:
Be sure to follow figures two and three when making your own cables. Do not use the ground lug on the XLR
connector. Do not connect the cable's shield conductor to the ground lug or allow the shield conductor to
come in contact with the XLR's outer casing. Grounding the shield could cause a short circuit and erratic
behavior.
Figure 1
If you are constructing your own data cables, be sure to use standard two conductor
shielded cable (This cable may be purchased at almost all professional sound and
lighting stores). Your cables should be made with a 3-pin male and female XLR
connector on either end of the cable. Also remember that DMX lines must be daisy
chained and can not be split.
High Power DMX Controller TV
is a HP LED control unit, specially used to drive 1 Watt high power LED
fixtures, such as High Power LED Bar.
High frequency driving HP LED bars suitable for CCD cameras pick up facility.
High Power DMX Controller TV
is engaged as a combination of a control interface and tension provider
for 1Watt high power LED fixtures.
Ability of the maximum of 6 channels can be controlled separately, allows a maximum loads of 3x350mA
per output and the maximum amount connected loads distributed over all 6 outputs must not exceed 6A.
All work modes and parameters can be set by flipping 10-way Function Dip Switch and 6-way Mode Dip
Switch.
USITT DMX512(1990) multiplexed digital control, via 3 pin XLR connector or terminals.
DMX Control Mode and Stand Alone Mode available .
1~7 patterns plus a sequence of 7 patterns, chase speed & fade time adjustable..
Different Output Group modes for user assignable.
Output loading modes available in R.G.B mode, WHITE mode and COOL WHITE& WARM WHITE mode.
Manual Dim mode allows to control overall output intensity.
AC 110-120V/AC220-240V power input option by voltage selector.
Providing built-in DC24V 6.5A
/
48V 3.2A PSU.
Power Failure Memory.
Full range voltage of
-2-
3.2 Data Cable (DMX Cable) Requirements:
Connect the
High Power DMX Controller TV
and your fixtures together using standard 3 pin DMX cables. The
High Power DMX Controller TV
uses DMX-512 protocol to operate your fixtures.
Figure 2
Figure 3
Line Termination. When longer runs of cable are used, you may need to use a terminator on the last unit to
avoid erratic behavior. A terminator is a 120 ohm 1/4 watt resistor which is connected between pins 2 and 3
of a male XLR connector (DATA + and DATA -). This unit is inserted in the female XLR connector of the last
unit in your daisy chain to terminate the line. Using a cable terminator will decrease the possibilities of
erratic behavior.
XLR Male Socket
1 Ground
2 Cold
3 Hot
XLR Female Socket
3 Hot
2 Cold
1 Ground
XLR Pin Configuration
Pin 1 = Ground
Pin 2 = Data Compliment (negative)
Pin 3 = Data True (positive)
DMX 512 OUT
3-PIN XLR
1
2
3
1
2
3
DMX 512 IN
3-PIN XLR
Special Note:
Termination reduces signal errors and avoids signal transmission
problems and interference. It is always advisable to connect a
DMX terminal, (Resistance 120 Ohm 1/4 W) between PIN 2 (
DMX-) and PIN 3 (DMX +) of the last fixture.
Figure 4
4.Product Layout & Functions
1. Dip Switches(10-way and 6-way):
Flip 10-way and 6-way Dip Switches to set some functions and modes for user's desired effects.
2. DMX Input:
3-Pin XLR male connector or terminal. Connect a universal DMX controller into this input for receiving DMX
values or DMX signals.
3. DMX Output:
3-Pin XLR female connector or terminal. Connect to next DMX fixtures for sending DMX values or DMX
signals.
4. Output:
6 terminal output connectors, allows a maximum loads of 3x350mA per output and the maximum amount
connected loads distributed over all 6 outputs must not exceed 6A.
-3-
4.1 Front Panel Layout
1
2
3
3-Pin XLR to 5-Pin XLR Conversion
Conductor
Ground/Shield
Data Compliment(-signal)
Data True(+signal)
Not Used
Not Used
3-Pin XLR Female(Out)
Pin 1
Pin 2
Pin 3
5-pin XLR Male(In)
Pin 1
Pin 2
Pin 3
Pin 4 - Do Not Used
Pin 5 - Do Not Used
5-Pin XLR DMX Connectors.
Some manufactures use 5-pin XLR connectors for DATA transmission in place of 3-pin. 5-pin XLR fixtures may
be implemented in a 3-pin XLR DMX line. When inserting standard 5-pin XLR connectors in to a 3-pin line a
cable adaptor must be used, these adaptors are readily available at most electric stores. The chart below
details a proper cable conversion.
4
2
3
1
Termination reduces signal errors and avoids signal transmission
problems and interference. It is always advisable to connect a
DMX terminal, (Resistance 120 Ohm 1/4 W) between PIN 2 (
DMX-) and PIN 3 (DMX +) of the last fixture.
Figure 4
4.Product Layout & Functions
1. Dip Switches(10-way and 6-way):
Flip 10-way and 6-way Dip Switches to set some functions and modes for user's desired effects.
2. DMX Input:
3-Pin XLR male connector or terminal. Connect a universal DMX controller into this input for receiving DMX
values or DMX signals.
3. DMX Output:
3-Pin XLR female connector or terminal. Connect to next DMX fixtures for sending DMX values or DMX
signals.
4. Output:
6 terminal output connectors, allows a maximum loads of 3x350mA per output and the maximum amount
connected loads distributed over all 6 outputs must not exceed 6A.
-3-
4.1 Front Panel Layout
1
2
3
3-Pin XLR to 5-Pin XLR Conversion
Conductor
Ground/Shield
Data Compliment(-signal)
Data True(+signal)
Not Used
Not Used
3-Pin XLR Female(Out)
Pin 1
Pin 2
Pin 3
5-pin XLR Male(In)
Pin 1
Pin 2
Pin 3
Pin 4 - Do Not Used
Pin 5 - Do Not Used
5-Pin XLR DMX Connectors.
Some manufactures use 5-pin XLR connectors for DATA transmission in place of 3-pin. 5-pin XLR fixtures may
be implemented in a 3-pin XLR DMX line. When inserting standard 5-pin XLR connectors in to a 3-pin line a
cable adaptor must be used, these adaptors are readily available at most electric stores. The chart below
details a proper cable conversion.
4
2
3
1
230
RISK OF ELECTRIC SHOCK
DISCONNECT INPUT POWER
BEFORE OPENING
N'OUVREZ PAS..RISQUE DE CHOC ELECTRIQUE
WARNING: THIS APPARATUS MUST BE EARTHED
POWER INPUT: 110-120VAC(3.2A) / 220-240VAC(1.6A), 50/60Hz.
CAUTION !
POWER IN
Made in PRC
VOLTAGE-SELECT
High Power DMX Controller TV
Product code: 95312351
5.2Stand Alone Mode
The Stand Alone Mode is engaged in by flipping the dip-switch 10 to the "OFF" position. And this mode includes
sub-modes with many functions, such as fade time, chasing speed, built-in programs.
1 2 3 4 5 6 7 8 9 10
ON
RS
ON
OFF
1,2,4
3,4
1,3,4
2,3,4
1,2,3,4
1,2,3,4,5,6,7,8,9
1
2
1,2
3
1,3
2,3
1,2,3
4
1,4
2,4
DMX ADDRESS (SLAVE)
SWITCHES ON
SWITCHES ON
(Dip Switch 10 = on)
START
CH#
START
CH#
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
..
511
..
..
..
..
..
..
..
1 2 3 4 5 6 7 8 9 10
ON
RS
DMX is short for Digital Multiplex. This is a universal binary language used as a form of communication
between intelligent fixtures. Each dip switch represents a binary value.
5.Operation Guide
A DMX value(address) is set by combining the different dipswitches that will add up to the value you wish to
achieve, for example:
Setting DMX address for 21.
Flip switches1,3,&5 to the
"ON" position
Setting DMX address for 201.
Flip switches1,4,7,& 8 to the
"ON" position
Dipswitches# Value
1=1
3=4
5=16
=21
Dipswitches# Value
1=1
4=8
7=64
8=128
=201
-4-
4.2 Rear Panel Layout
1. Power Input: AC110~120V(3.2A) /AC220~240V(1.2A), 50~60Hz.
2. Voltage Selector: AC120V/230V optional by this voltage selector.
In this mode, the dip-switch 10 is flipped to the "ON" position. And this switch sometimes used to activate
some fixture special functions.
Dip Switch 1 address equals 1
Dip Switch 2 address equals 2
Dip Switch 3 address equals 4
Dip Switch 4 address equals 8
Dip Switch 5 address equals 16
Dip Switch 6 address equals 32
Dip Switch 7 address equals 64
Dip Switch 8 address equals 128
Dip Switch 9 address equals 256
5.1 DMX Control Mode
(DMX Addressing)
1
2
