Deagostini MODEL SPACE Robi Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 32

background image

You will be using parts from the
previous stages, so be sure to have
these to hand before beginning.

STAGE 60: PREPARE

AND FIT ROBI’S

HEAD SERVOS

Prepare Robi’s second head servo then fit it, along with the

one from the previous stage, to his head servo frame.

There are two servos inside the upper
part of Robi’s head, ID=14 and ID=15.
Both are set onto the head servo
frame that you fitted and wired over
the previous stages, and they will work
in tandem with the internal lever and

head base to make Robi’s head tilt
forward and back (in the case of
ID=15) and side to side (ID=14). As
ever, take care when handling open
servos, and make sure you set the
correct ID number.

ASSEMBLY GUIDE

1

PARTS TO BE

ASSEMBLED

1 Servo motor (ID=14)

YOUR PARTS

SAVED PARTS

Neck stand

(Stage 53)

Battery

(Stage 38)

Power distribution board

(Stage 40)

Body and neck assembly, and

servo cable (Stage 59)

328

«
...
9
10
11
12
13
...
»

Содержание MODEL SPACE Robi

































Отзывы:

Нет отзывов

Похожие инструкции для MODEL SPACE Robi

Бренд: SunFounder Страницы: 50

Solar Power Project Pack

Бренд: Mindsets Страницы: 4

Бренд: Tibhar Страницы: 14

Learn 'N' Fun Robot

Бренд: Radio Shack Страницы: 2

Бренд: XYZrobot Страницы: 46

ROBO MAX TR41573

Бренд: Spectron Toys Страницы: 12

BUILD UP RC MINI ROBOSAPIEN

Бренд: WowWee Страницы: 2

Бренд: WowWee Страницы: 2

Бренд: Kitronik Страницы: 8

Бренд: Kitronik Страницы: 8

BBC Micro Bit move Mini Mk2

Бренд: Kitronik Страницы: 8

Angle Armed Quad

Бренд: Flybrix Страницы: 41

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды