de Gier GXP10 Скачать руководство пользователя страница 23

Страница: 23 / 26

De Gier B.V., Westlandseweg 9, 2291 PG WATERINGEN, THE NETHERLANDS,

+31 (0)174 292089, [email protected], www.degierdrivesystems.com

Versie 1 – 2020 / 03 / 01

Glossary

Benaming

Verklaring

S3-30%

Load cycle as defined in IEC 60034-1, Intermittent periodic operation with the

motor operational during 30% of the time as a max.

Alternating Current (“wisselstroom”).

Afschermkap

Cover used to prevent direct contact between persons, rain, dust and the motor

gearbox.

Axiaal

In the longitudinal direction of the shaft.

Aanhaalmoment [Nm]

Torque to which a bolted joint has to be tightened, expressed in Newton meter.

dB(A)

Intensity of sound, expressed in decibel.

Bedrijfsurenteller

A counter that keeps the actual number of operating hours of the drive.

Bimetaal

Temperatuur beveiligingsschakelaar.

Compensatiekoppeling

A coupling that is able to is compensate alignment errors, for instance a chain

coupling, universal joint or cardan shaft.

Direct Current (“gelijkstroom”).

Dodemanssysteem

Emergency switch operated by a pull cord along the entire length of the installa-

tion.

Elektrische aansluitwaarden

The voltage, current and power values that the electric motor was designed for.

These can be found on the rating plate of the electric motor.

Gevarenzone

The area below or in the direct vicinity of the driven/moving parts.

Hangende lasten

Machinery or machine parts which are hanging from steel cables or lifting straps

and are not supported otherwise.

Hiërarchisch hogere functie

An overriding or governing switch condition, depending on the structure of the

system. For example, a rain detection that can cause the motor gearbox to start

automatically.

Koppel [Nm]

Measure for rotation-effect of a force. The magnitude of the torque is equal to

the force times the arm and is expressed in Newton meter.

Lineair

Straight line.

Mechanische rem

Electro-magnetically operated brake on the rear of the electric motor. Loss of the

power causes the brake to be engaged. When the power comes back the brake

will be disengaged again.

Motorreductor

An (electric)motor with gear unit to reduce the shaft speed.

Radiaal

A force perpendicular to the shaft.

Relais

A switch operated by an electro-magnet.

Содержание GXP10



























Результаты поиска

Содержание GXP10

Отзывы:

Бренды по названию

Популярные бренды

de Gier GXP10, Инструкция по установке

Результаты поиска

Содержание GXP10

Отзывы:

Бренды по названию

Популярные бренды