background image

 

Explanation of graphical symbols

The lightning symbol within a triangle is intended to alert

the user to the presence of uninsulated "dangerous

voltages" within the unit’s chassis that may be of

sufficient magnitude to constitute a risk of electric shock

to humans.

 

The exclamation point within a triangle is intended to

alert the user to the presence of important operating and

service instructions in the literature accompanying the

product.

Before using this product, carefully read the

applicable items of the following safety instructions.

 

 

1. Keep these instructions for future reference.
2. Read these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Keep water or other liquids away from the unit. Do not place

liquid filled containers, for example beverages, on top of the

unit.

6. Do not operate the unit while it is wet or standing in liquid.
7. Always operate the unit with the chassis ground wire

connected to the electrical safety earth. Do not defeat the

safety purpose of a grounding-type plug. A grounding-type

plug has two blades and a third grounding prong. The third

prong is provided for your safety. If the provided plug does

not fit into your outlet, consult an electrician for replacement of

the obsolete outlet.

8. Do not use this unit if the power cord is damaged or frayed.

Protect the power cord from being walked upon or pinched,

particularly at the plugs and the point where it exits from the

apparatus.

9. The unit is intended for use in a 19" rack. Follow the mounting

instructions. When a rack on wheels is used, exercise caution

when moving the loaded rack to avoid injury from tipping

over.

10. Unplug this apparatus during lightning storms or when unused

for long periods of time.

 

11. Lay all cables connected to the unit carefully so that they

cannot be crushed by vehicles or other equipment and that no

one can either step on them or trip over them.

12. Refer all servicing to qualified service personnel. Servicing is

required when the apparatus has been damaged in any way

such as:

– Power-supply cord or plug is damaged.
– Liquid has been spilled into the unit.
– An object has fallen into the unit.
– The unit has been exposed to rain or moisture.
– The unit does not operate normally.
– The unit was dropped or the chassis is damaged.
– Do not remove top or bottom covers. Removal of the covers

will expose hazardous voltages. There are no user

serviceable parts inside and removal may void the warranty.

13. Use the mains plug as the disconnecting device and keep it

readily accessible. If the mains plug is not readily accessible

due to mounting in a 19" rack, then the mains plug for the

entire rack must be readily accessible.

14. An experienced user must always supervise the equipment,

especially if inexperienced adults or minors are using the

equipment.

IMPORTANT SAFETY INSTRUCTIONS

 

d&b DS10 Manual 1.5 en

3

Содержание DS10























Отзывы: