background image

Raider Pro 250 (single-seat / double-seat): Service Manual                                    EEC Version: 1.0  Oct.. 2004 

 

4

1. 

General Information 

 

1.1 Model Identification 

1.1.1 Frame Number 

The frame number or VIN is stamped under the seat on the vehicle frame and is stuck behind the 

seat. 

 

1.1.2Engine Number 

The engine number is located on the upper right rear engine case. 

 

 

 

 

 

 

 

 

 

 

1.2 Fuel and Oil Recommendations 

Be sure to use the specified fuel and oil 
 

1.2.1 Fuel 

Please use the gasoline of SAE 90# or above.   
Also we recommend you to use the unleaded gasoline. 

 

1.2.2 Engine Oil 

Please use the high-quality engine oil of SAE 10w/30SF. 

 

1.3 Break-in Procedure 

For your first 2 hours of riding, don’t exceed 2/3 throttles. 
Vary the engine speed for the first 5 hours. 
Never hold the engine at full throttle for long periods of time. 

 

1.4 Specifications 

DIMENSIONS                  SINGLE-SEAT / DOUBLE-SEAT 

Overall Length 

 

 

 

       2250mm  / 2270mm 

Overall Width  

 

 

 

       1360mm  / 1610mm 

Overall Height  

 

 

 

       1550mm  / 1533mm 

Содержание Raider Pro 250 S
































Отзывы: