daviteq Sigfox WSSFC-PPS Скачать руководство пользователя страница 2

Страница: 2 / 23

STEP 3: Configure the sensor's operating parameters

Configure parameters like cycle send data, alarm, a, b,...

Refer to the configuration

section 5

STEP 4: Add device to Backend Sigfox

refer to section 5.4 for details

STEP 5: Installation

refer to section 7 for details

Document Ver.

Release Date

Change log

1.0

SEP-2020

- First version for WSSFC-PPS

1.1

FEB-2022

- Update information

WSSFC-PPS is a Sigfox node integrated Process Pressure Sensor, and it has diﬀerent kinds of measurements, such as

Gage/Absolute/Sealed Gage, range -1 .. + 700 bar, high accuracy, and stability. The sensor will transmit data in kilo-

meters distance to Sigfox basestation. WSSFC-PPS can support all regions of Sigfox network in over the World, RC1,

RC2, RC3, RC4, RC5, RC6, RC7.

SENSORS SPECIFICATION:

Sensor

Advanced PIEZO technology

Measurement range

Select from -1 .. + 700 bar Gage/Absolute/Sealed Gage

1. Change Log

2. Introduction

3. Specification

Содержание Sigfox WSSFC-PPS
























Результаты поиска

Содержание Sigfox WSSFC-PPS

Отзывы:

Бренды по названию

Популярные бренды

daviteq Sigfox WSSFC-PPS, Руководство пользователя

Результаты поиска

Содержание Sigfox WSSFC-PPS

Отзывы:

Бренды по названию

Популярные бренды