manualshive.com logo in svg

daviteq Sigfox WSSFC-PPS, Руководство пользователя

Поделиться
Скачать
daviteq Sigfox WSSFC-PPS Скачать руководство пользователя страница 19

Base station. In real life, there may be no LOS condition. However, the Sigfox sensor still communicate with Base

station, but the distance will be reduced significantly.

Consider to use the isolation valve 1/2" or 1/4" to isolate the media and the sensor during maintenance;

Fully closing the isolation valve during installation and maintenance the sensor;

Fully open the isolation valve during normal operation;

There are two ways of process mounting as below.

The total weight of the sensor MUST be within the permitted load of the pipe to be installed;

Consider to build the support for the pipe if the sensor weight is larger than the permit;

Below picture shown without the isolation valve, but we highly recommend to use isolation valve.

ATTENTION:

DO NOT

 install the Sigfox sensor or its antenna inside a completed metallic box or housing, because RF signal

can not pass through metallic wall. The housing is made from Non-metallic materials like plastic, glass, wood,

leather, concrete, cement…is acceptable.

7.2 Process mounting

WARNINGS:

1. Please make sure the fluid is suitable with the wetted materials of the sensor. Please refer sensor

specification;

2. Please make sure the operating temperature and pressure is suitable with the sensor. Please refer sensor

specification;

3. Prepare the professional tools for installation. The inappropriate tools may cause damage to the sensor.

DANGER:

1. The installer need to be equipped with full Safety gears during installation, such as safety glasses, safety

shoes, safety cloths, safety mask...Please follow the safety instructions of the installation site;

2. The installer must be qualified for this installation job;

3. The installer must be permitted by Site's owner for performing the installation;

7.2.1 Mounting direct on Pipe

Содержание Sigfox WSSFC-PPS
























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды