DAVIS Vantage Pro2 Updater Скачать руководство пользователя | Manualshive

Страница: 35 / 48

background image

32

Console and WeatherLink Configuration

The Vantage Pro2 console, Weather Envoy, and corresponding WeatherLink (version 5.6
or higher) software for Vantage Pro2 allow you to view the information coming from the
stations in your network and view information directly related to your repeater network.

Repeater Information on the Console

Once you have configured your console to receive station data through a repeater net-
work, the console keeps track of and displays diagnostics related to the wireless repeater,
such as battery status and network signal strength.

Note: See “Verifying Repeater Communication with a Console” under the installation procedures you used to

install your wireless repeater network.

Battery Information on the Console

Whenever any station or repeater in the network detects a low battery, the console dis-
plays a low battery warning for that repeater in the ticker tape display in the console’s
Current Weather Mode:

Note: The console displays low battery messages only for the first four repeaters/stations in the network that

run low on battery power. If there are more than four repeaters/stations in your network experiencing low
battery power at a time, the console does not display all of them.

Network Signal Strength

As a diagnostic tool, the console can display the received signal strength of a repeater
from the previous station/repeater in the network.

Note: The signal strength information will display in the wind compass for the station the console is set to

receive as an ISS or Anemometer Transmitter Station. Use Screen 2 of the Setup Mode to temporarily
reconfigure a non-ISS station as an ISS during the test if necessary. Display the Current Weather Mode
again and press WIND again to view the signal strength. If there is more than one station, reconfigure
each station the same way and repeat the process.

Using this function lets you analyze the communication efficiency for repeaters and
transmitters in the network or find the optimal repeater location.

To view the signal strength between repeater and the previous transmitter in the chain:

1. Make sure the repeater’s Test Mode is on (Test Switch #4 is set ot ON) to test its signal

strength.

2. In the console’s Setup Mode, configure the console to receive an ISS station repeated

by the repeater.

3. In the console’s Current Weather Mode, press WIND. The signal strength between the

repeater and the previous transmitter in the chain displays when the degree (º) sign is
visible in the center of the wind compass rose.

«
...
33
34
35
36
37
...
»

Содержание Vantage Pro2 Updater

















































Отзывы:

Нет отзывов

Похожие инструкции для Vantage Pro2 Updater

Бренд: LAUMAS Страницы: 40

Бренд: Metra Electronics Страницы: 14

Speedglas G5-02

Бренд: 3M Страницы: 17

Speedglas 9100 MP

Бренд: 3M Страницы: 72

Speedglas 9100-Air

Бренд: 3M Страницы: 63

Бренд: 3M Страницы: 84

Бренд: YOKOGAWA Страницы: 12

Бренд: FeiYu Tech Страницы: 14

Бренд: RADEMACHER Страницы: 48

Бренд: YUNEEC Страницы: 6

Бренд: Harol Страницы: 16

Бренд: Yakima Страницы: 6

Бренд: Yakima Страницы: 18

Бренд: Yakima Страницы: 18

Бренд: Dufco Страницы: 11

Бренд: Klarstein Страницы: 29

Wireless Handsfree Car Kit

Бренд: Wagan Страницы: 20

X-903 Ultra Carbon 29

Бренд: X-lite Страницы: 116

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды