DAVIS Vantage Pro2 Updater Скачать руководство пользователя | Manualshive

Страница: 26 / 48

background image

23

In this example, the console is set up to receive an ISS station with transmitter ID 1
from repeater C..

4. Press DONE to continue to other screens in Setup Mode, or press and hold DONE to

return to Current Weather Mode.

Note: See the

Vantage Pro2 Console Manual

for more information on the Setup Mode screens if necessary.

To verify that setup was successful, in the console’s current mode:

View the transmitter information displaying at the bottom of the console screen.
If the transmitter ID being repeated is displayed and an “X” flashes in the bottom
right-hand corner of the ticker tape, the transmitter is being repeated and received by
the console successfully.

Multiple Transmitters/One Repeater
Installation

A multiple transmitter/one repeater installation differs from a single repeater installation
only in the number of transmitters the repeater listens to and repeats. See “Single
Repeater Installation” on page 13 for detailed instructions on configuring the transmitter
and console for wireless repeater use.

This section covers the additional steps necessary to configure the repeater to listen to
more than one station.

Verifying Repeater ID

The wireless repeater contains a DIP switch used to program
the repeater with a unique identification. DIP switches #1, 2
and 3 on the repeater are used in the same way that DIP
switches are used on all stations. The default repeater ID is
A and the default position for the DIP switches is down or OFF.

Note: For installations in which only one repeater is involved, the repeater should remain on the default ID of A

and should not be changed.

1

Repeater DIP
Switch Set to A

«
...
24
25
26
27
28
...
»

Содержание Vantage Pro2 Updater

















































Отзывы:

Нет отзывов

Похожие инструкции для Vantage Pro2 Updater

Бренд: T-Tech Страницы: 38

Бренд: 7AMEnfant Страницы: 2

Бренд: Omnicomm Страницы: 20

Бренд: omnicharge Страницы: 12

Бренд: quadient Страницы: 2

AcousticDesign AD-S52

Бренд: QSC Страницы: 4

Extreme Racing 15

Бренд: Odyssey Страницы: 4

Бренд: Homelite Страницы: 1

Бренд: U & Me Brothers Страницы: 6

Бренд: Urban Factory Страницы: 2

Бренд: Ravelli Страницы: 9

Car Cup Holder Phone Mount

Бренд: UGREEN Страницы: 9

Бренд: Nauticam Страницы: 2

Бренд: tams elektronik Страницы: 44

Бренд: Feniex Страницы: 5

Бренд: Reflecta Страницы: 15

Бренд: Yakima Страницы: 9

Efector 200 OGE08 Series

Бренд: IFM Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды