DAVIS Vantage Pro2 Updater Скачать руководство пользователя | Manualshive

Страница: 2 / 48

background image

Vantage Pro2

™

Wireless Repeater Manual

Rev. C, October 18, 2005
Document Part Number: 07395.238
For Vantage Pro2 Wireless Repeaters: 7626, 7627

Vantage Pro

®

and Vantage Pro2

™

are trademarks of Davis Instruments Corp., Hayward, CA.

© Davis Instruments Corp. 2005. All rights reserved.
Information in this document subject to change without notice.

3465 Diablo Avenue, Hayward, CA 94545-2778

510-732-9229 • Fax: 510-732-9188

E-mail: [email protected] • www.davisnet.com

FCC Part 15 Class B Registration Warning
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment on and off, the user is encour-
aged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Changes or modification not expressly approved in writing by Davis Instruments may void the warranty and void the user's
authority to operate this equipment.

FCC ID: IR2DWW765Y
IC: 3788A-765Y

EC EMC Compliance
This product complies with the essential protection requirements of the EC EMC Directive 89/336/EC, as tested to the follow-
ing directives:
• ETSI EN 300 220
• ETSI EN 301 489

Transmitter and Repeater ID Worksheet

List the transmitter types and circle the transmitter IDs used:

Circle last Repeater ID used:

A

B

C

D

E

F

G

H

Transmitter Type

Transmitter ID

1

2

3

4

5

6

7

8

«
1
2
3
4
...
»

Содержание Vantage Pro2 Updater

















































Отзывы:

Нет отзывов

Похожие инструкции для Vantage Pro2 Updater

Бренд: Palm Страницы: 14

Бренд: Toco Страницы: 12

Бренд: Abibird Страницы: 2

Бренд: Abicor Binzel Страницы: 20

Бренд: Danfoss Страницы: 4

Бренд: Karma Страницы: 7

Бренд: Zhiyun Страницы: 10

Бренд: Razorri Страницы: 26

Бренд: Quantum Страницы: 3

480L - UPDATE V3.0

Бренд: Lexicon Страницы: 40

Бренд: SeaSucker Страницы: 9

Бренд: eufy Security Страницы: 12

Drive Pro EZ Build 41130

Бренд: Meyer Страницы: 11

Бренд: White Outdoor Страницы: 4

Бренд: PASCO Страницы: 4

Бренд: Amazon Страницы: 100

TRIUMPH Bonneville T 120

Бренд: hepco & becker Страницы: 4

Бренд: Peg-Perego Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды