background image

1

The DriveRight

®

 SmartCard System

Introduction

The DriveRight

®

 SmartCard System allows you to download DriveRight data 

from any DriveRight device using the SmartCard On-Board Reader (#8105), 
transport it to a computer easily using the SmartCard Desktop Reader (#8108) 
and SmartCards (#8112), and also transfer administrative data from the com-
puter to the DriveRight. 

The SmartCard System can also be used with the optional Starter Interrupter 
Kit (#8116) to prevent unauthorized drivers from using a vehicle or vehicles. 
The DriveRight Fleet Management Software (#8186) should be used to set up 
and maintain the SmartCard System operations. It is also required to configure 
the SmartCards. All DriveRight 600 (#8156) and 600E (#8126) models work 
with the SmartCard system. 

Before You Install

Because the specific installation of the SmartCard System hardware can vary 
considerably from vehicle to vehicle, these instructions are intended to be a 
general guide for the professional installer or experienced mechanic. We 
strongly recommend that you read the entire manual before beginning the 
installation. Be sure you understand each procedure thoroughly before starting 
that procedure.

CAUTION: Installing SmartCard hardware or any of the DriveRight components in a vehicle 

can be hazardous to both the installer and to the vehicle’s electrical system. This 
manual assumes you are aware of the inherent dangers of working in and around 
a vehicle and have a working understanding of electricity. If you are uneasy about 
any part of the installation, please have an ASE-certified technician or professional 
mechanic do the installation. Davis Instruments specifically disclaims any liability 
for injury or loss resulting from the installation or use of DriveRight Products.

The SmartCard System

The SmartCard System consists of four products:

• The SmartCard (#8112 - Pack of 10)

• The SmartCard On-Board Reader (#8105) - Includes one SmartCard

• The SmartCard Desktop Reader (#8108)

• The Starter Interrupter Kit (#8116 - Optional)

SmartCard

The SmartCard is a small plastic card about the size of a credit card that con-
tains a memory chip for storing and transporting all the DriveRight data easily. 
A pack of 10 SmartCards (# 8112) is available for purchase. 

Содержание 8105

















Отзывы: