manualshive.com logo in svg

Dave Smith Instruments Prophet Rev2, Руководство пользователя

Поделиться
Скачать
Dave Smith Instruments Prophet Rev2 Скачать руководство пользователя страница 35

25

Prophet Rev2 User’s Guide

Amplifier Envelope

Delay:

 0...127

—Sets a delay between the time the envelope is triggered 

(note on) and when the attack portion actually begins. 

Attack:

 0...127

—Sets the attack time of the envelope. The higher the 

setting, the slower the attack time and the longer it takes for the filter to 
open from the level set with the filter 

cutoff

 knob to the level set by the 

filter envelope amount. Percussive sounds typically have sharp (short) 

attacks.

Decay:

 0...127

—Sets the decay time of the envelope. After a sound 

reaches the filter frequency set at its attack stage, 

decay

 controls how 

quickly the filter then transitions to the cutoff frequency set with the 

sustain

 knob. The higher the setting, the longer the decay. Percussive 

sounds, such as synth bass, typically have shorter decays (and a generous 

amount of low-pass filter resonance).

Sustain:

 0...127

—Sets the filter cutoff frequency for the sustained 

portion of the sound. The sound will stay at this filter frequency for as 

long as a note is held on the keyboard.

Release:

 0...127

—Sets the release time of the envelope. This controls 

how quickly the filter closes after a note is released.

Amplifier Envelope

After passing through the filters, a synthesized sound goes into an analog 
voltage controlled amplifier or VCA, which controls its overall volume. 
The VCA has a dedicated, five-stage envelope generator (DADSR). 

The Amplifier Envelope is used to shape the volume characteristics of a 

sound over time by giving you control over its attack, decay, sustain, and 
release stages (plus a delay parameter to delay the onset of the envelope). 

Along with the filter envelope, this is one of the most important factors 

in designing a sound. 

Without a volume envelope, the volume of a sound wouldn’t change 
over the duration of a note. It would begin immediately, remain at its full 
volume for the duration of the note, then end immediately when the note 
was released. Again, that’s not very interesting sonically and it’s not typi-
cally how instruments behave in the real world. 

Содержание Prophet Rev2











































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды