Datex-Ohmeda D-VHC17 Скачать руководство пользователя страница 35

Страница: 35 / 72

Displays and Controller Boards

Document No. 8001004-1

Check that the LCD display functions normally after the performed electrical safety check.

10.

Clean the LCD display with suitable detergent.

•

Fill in all necessary documents.

3.3

Disassembly and reassembly

3.3.1

LCD Display, V-LCC10 A/W

Disassemble the LCD Display according to the following procedure. Please refer to the exploded

view of the LCD Display.
NOTE: Wear a static control wrist strap and soft cotton gloves (dust free) when handling the LCD

Display parts. Do not touch connector pins

Place the LCD Display on a flat surface the front side downwards.

Remove the screws (4) that are located at the corners of the rear panel.

Lift the rear panel gently, disconnect the cable(s) and set the rear panel aside.

Rev. 03, 04

In normal circumstances it is very difficult to keep the LCD Display component and the LCD Display

shield free of dust when those are detached from the LCD Display frame. If dust particles remain on

the LCD Display component and LCD Display shield surfaces, those may impair the quality of

picture on the screen.
In case you need to detach the LCD Display component for repair, if you can provide a dust free

environment, follow the instructions below. Otherwise, you may return the whole LCD Display to be

repaired at Datex-Ohmeda.
NOTE: If the LCD Display unit is broken, handle it carefully to avoid injury (the LCD Display

component and the backlight lamp are made of glass). Wash your hands if you touched liquid

crystal which may flow out from a broken LCD Display component.
NOTE: Do not touch , push or rub the exposed soft polarizer. Keep the polarizer clean. In case of

accidental mishandling see the instructions following this chapter.
1.

The Adapter board and its insulation plate can be detached by disconnecting the cable

connectors and removing the screws (4).

Remove the screws (8) that are located at the back of the LCD Display unit.

The following parts can now be lifted off one by one:

−

the Adapter unit

−

the LCD Display component with the backlight

−

the LCD Display shield

−

the EMC cover with the LCD Display gasket

Содержание D-VHC17









































































Результаты поиска

Содержание D-VHC17

Отзывы:

Бренды по названию

Популярные бренды

Datex-Ohmeda D-VHC17, Техническое справочное руководство

Результаты поиска

Содержание D-VHC17

Отзывы:

Бренды по названию

Популярные бренды