background image

 

 

 

FCC Compliance Statement 

This  device  complies  with  part  15  of  the  FCC  rules.  Operation  is  subject  to  the  following  two 
conditions: 

1.

 

This device may not cause harmful interference, and  

2.

 

This  device  must  accept  any  interference  received,  including  interference  that  may  cause 
undesired operation. 

Warnings and Precautions 

1.

 

Read all of these warnings and save them for later reference. 

2.

 

Follow all warnings and instructions marked on this unit. 

3.

 

Unplug this unit from the wall outlet before cleaning. Do not use liquid or aerosol 
cleaners. Use a damp cloth for cleaning. 

4.

 

Do not use this unit in or near water.  

5.

 

Do  not  place this  unit  on  an unstable  cart,  stand,  or table.  The unit  may fall,  causing  serious 
damage. 

6.

 

Slots and openings on the cabinet top, back, and bottom are provided for ventilation. To ensure 
safe  and  reliable  operation  of  this  unit,  and  to  protect  it  from  overheating,  do  not  block  or 
cover  these  openings.  Do  not  place  this  unit  on  a  bed,  sofa,  rug,  or  similar  surface,  as  the 
ventilation openings  on the  bottom  of the  cabinet  will  be  blocked.  This unit  should  never  be 
placed  near  or  over  a  heat  register  or  radiator.  This  unit  should  not  be  placed  in  a  built-in 
installation unless proper ventilation is provided. 

7.

 

This product should only be operated from the type of power source indicated on the marking 
label  of  the  AC  adapter.  If  you  are  not  sure  of  the  type  of  power  available,  consult  your 
Datavideo dealer or your local power company. 

8.

 

Do not allow anything to rest on the power cord. Do not locate this unit where the power cord 
will be walked on, rolled over, or otherwise stressed. 

9.

 

If an extension cord must be used with this unit, make sure that the total of the ampere ratings 
on the products plugged into the extension cord do not exceed the extension cord rating. 

10.

 

Make sure that the total amperes of all the units that are plugged into a single wall outlet do 
not exceed 15 amperes. 

11.

 

Never push objects of any kind into this unit through the cabinet ventilation slots, as they may 
touch  dangerous  voltage  points  or  short  out  parts  that  could  result  in  risk  of  fire  or  electric 
shock. Never spill liquid of any kind onto or into this unit. 

12.

 

Except  as  specifically  explained  elsewhere  in  this  manual,  do  not  attempt  to  service  this 
product yourself. Opening or removing covers that are marked “Do Not Remove” may expose 
you  to  dangerous  voltage  points  or  other  risks,  and  will  void  your  warranty.  Refer  all  service 
issues to qualified service personnel. 

13.

 

Unplug  this  product  from  the  wall  outlet  and  refer  to  qualified  service  personnel  under  the 
following conditions: 
a.

 

When the power cord is damaged or frayed; 

b.

 

When liquid has spilled into the unit; 

c.

 

When the product has been exposed to rain or water;  

Содержание TLM-170F





















































Отзывы: