Operating the Alarm
To arm the alarm:
With the ignition switched off, press the large button on the remote control. The indicators
will flash twice and if arm/disarm tones are enabled, a double chirp will be heard. The LED will illuminate for 3
seconds and then flash once every second for a further 10 seconds whilst the system initializes the tilt sensor
and trigger inputs. After 10 seconds, the alarm is fully armed. If the automatic arming function is enabled the
alarm will fully arm automatically without further user input after the ignition is switched off, the delay period
can be chosen by the user from 30seconds, 1 minute or 2 minutes.
When fully armed the LED flash rate will be determined by the vehicle battery voltage* as follows:
Fully charged (>11.5v) LED flashes once every 5 seconds
Partially discharged (10.5V to 11.5V) LED flashes every 10 seconds
Low Battery (<10.5v) LED flashes every 20 seconds
* Voltages are approximate.
Note:
-
Alarm cannot be disarmed within 3 seconds of arming.
-
If armed in Transport/ Service mode the LED will flash in groups of 2 flashes, indicating the
movement sensor is disabled.
To arm/disarm silently (when tones are enabled):
With the ignition switched off, press the small button and
then within 3 seconds press the large button. The alarm will arm/disarm as normal except the chirp will be off
for that one operation.
To arm in transport mode:
With alarm the disarmed and ignition off, press the large button to arm the alarm.
The siren will chirp twice (if arm/disarm tones are activated) and the indicators will flash twice to indicate the
alarm has been armed.
Then within 3 seconds press the small button. The siren will chirp one extra time and the indicators will flash
again once to indicate the tilt sensor has been disabled.
To disarm the alarm:
Press the large button on the remote control. The indicators will flash once, the LED will
extinguish and a single chirp will be heard (if arm/disarm tones are activated). The alarm cannot be rearmed
within 3 seconds of disarming.
If the alarm system has triggered
Upon disarming the alarm the siren will beep 4 times and
then the LED will flash and the siren will chirp indicating
the trigger circuit. If the ignition is cycled on then off the
sequence will repeat. Arming the alarm system or turning
the ignition on for more than one minute will erase the
trigger memory
Disarming with PIN code:
With the alarm in the armed state turn the ignition on/off/on/off/on within 7
seconds (the alarm will sound).
The LED will start to flash rapidly for 3 seconds then flash slowly a maximum of 9 times. Count the LED flashes,
and then switch the ignition off when the LED flash equals that of the first digit of the PIN code. Zero would be
input by immediately switching the ignition off after the rapid flashing of the LED. Switch the ignition back on
and start the LED count process again. Repeat this process for the 2
nd
, 3
rd
and 4
th
digits of the provided PIN.
If the PIN code has been entered correctly the alarm will disarm, if entered incorrectly the alarm will continue
to sound, at this point the PIN code can be entered twice more before PIN code entry is disabled for two
minutes.
DATATOOL
EVO
PLUS
User Guide
Disarming with Trigger Input (‘Keyless Ignition’ vehicles):
With the alarm armed gain access to the trigger
switch. Apply the trigger switch magnet to the switch, then remove and repeat 3 times within 7 seconds, e.g.
apply/remove/apply/remove/apply/remove. The alarm will sound if not already doing so. Note: to apply the
magnet to the switch, the magnet must be within 10mm of the switch, with both magnet and switch aligned
along a long edge, and should be held in position for at least 1 second. Also to remove the magnet the magnet
should be at least 100mm away from the switch, and should be held in position for at least 1 second.
The LED will start to flash rapidly for 3 seconds then flash slowly a maximum of 9 times. Count the LED flashes,
and then apply the magnet to the switch when the LED flash equals that of the first digit of the PIN code. Zero
would be input by immediately applying the magnet to the switch after the rapid flashing of the LED.
Remove the magnet from the switch, the LED will start to flash rapidly for 3 seconds then flash slowly a
maximum of 9 times. Count the LED flashes, and then apply the magnet to the switch when the LED flash
equals that of the second digit of the PIN code. Zero would be input by immediately applying the magnet to
the switch after the rapid flashing of the LED. Repeat for the third and fourth digit.
If the PIN code has been entered correctly the alarm will disarm, if entered incorrectly the alarm will continue
to sound, at this point the PIN code can be entered twice more before PIN code entry is disabled for two
minutes.
To add a new transmitter on keyless ignition vehicles:
Disarm the alarm either via remote or by PIN entry
above. Enter the system PIN as detailed above and once the PIN is entered immediately pressing a remote
control, existing or new will add this to the system and delete all previously entered remote controls. Press
each remote control that you require to be added; the siren will chirp and the LED will flash for
acknowledgement of the remote control. If the maximum number of remotes has been reached then a long
beep will be heard indicating that the last remote pressed has not been saved.
Turning on the ignition, or pressing an already entered remote control, or not pressing a button on a new
remote control for 30 seconds will exit this mode. On exit the alarm will chirp twice and the LED will flash the
number of stored remote controls.
Triggering the Alarm
The alarm can be triggered by the following actions: ignition on; change of state trigger input (Seat switch); tilt
trigger; panic button; power removed and power with ignition re-applied.
When triggered the siren will sound and the indicators will flash for 29 sec. The alarm will then re-arm. If the
fault is still present then the alarm will trigger again. Ignition, tilt, and change of state can only trigger a
maximum of 10 times before the circuit in question is disabled. Panic will sound continuously, on for 29
seconds then off for 5 seconds and repeat. Power removed will sound for one 29 second cycle every time the
ignition power is reapplied.
Optional Features
Bike finder:
When the alarm is armed, press and hold the small button to activate the ‘bike finder’
feature which flashes the indicators 10 times.
Panic mode:
Holding down the large button for 3 seconds will sound the siren and flash the indicators.
Press the large button once to stop the siren. Feature will operate in armed state with ignition on or off,
and disarmed state with ignition off.
Long term storage mode:
When disarmed with ignition off, hold down both buttons on the remote
control for 10 seconds, a loud chirp will be heard and the alarm will now be inactive. All alarm functions
will be disabled, including remotes and the vehicle will be immobilised.
To exit long term storage mode, turn on the ignition. An ascending tone will be heard and the large
remote control button must be pressed within 10 seconds otherwise the alarm will sound.
www.datatool.co.uk
Number of flashes/chirps:
(
(
1
)
)
Ignition circuit
(
(
2
)
)
Seat switch
(
(
3
)
)
Movement alert
(
(
4
)
)
Panic function activated
(
(
5
)
)
Power (vehicle battery) removal
