background image

 
 
 

iBootBar 

– Precision Version 

 

   

Page 7 

iBootBar_Precision_20160428e.doc 

 

Firmware ver 1.41.32 

 

  

 

Configuration 

Accessing the Command Line Interface 

All configuration parameters and outlet changes are set using the Command Line Interface (CLI). The CLI is 
accessed through the network, using a telnet client, or through the serial port, or data modem using a terminal client. 
 
Open a telnet client and point it to the current IP Address.   (Factory Default is 

192.168.0.254

 
Connect to the Serial port or via dial modem (-M versions)  (Factory Default is 

115200,8,n,1

)  

 
Upon connection, press Enter, then enter the username and password when prompted 
(Factory Default for both is 

admin

 
It is possible to bypass the authentication requirements when used with direct RS-232 or on secure networks.   
 
A complete list of valid commands and syntax is found on page 9 and 10.    
 

Setting  the IP Address 

iBootBar comes with factory installed IP address 192.168.0.254  
 
There are three techniques to setting the IP address of the iBootBar.   
 

1.  Terminal Client software via Telnet, Serial, Modem. 
2.  Automatically from a DHCP Server  
3.  ARP / Ping 

 
To configure the mode to set the IP address, access the iBootBar command line interface (CLI) and use the set 
ipmode command as indicated below.   

Setting the IP address using CLI 

The following commands are used to set the IP parameters 
 

set ipaddress <dotted decimal>  

ex. 192.168.0.125 

set subnet <dotted decimal> 

ex. 255.255.255.0 

set gateway <dotted decimal>  

ex. 192.168.0.2 

 

If you wish to prevent DHCP or ARP-Ping from altering the IP Address, also enter the following command 

set ipmode static 

Changing any of these values will require a reboot of the unit.  Type the command “reboot” as indicated, press the 
reset pushbutton on the front panel, or remove and restore all power to the iBootBar. 

Setting the IP address from a DHCP Server 

A DHCP server will automatically assign an IP address (dynamic address) as well as Subnet Mask and Gateway to 
the iBoot.   

 

To enable this feature, configure the iBootBar with the command   

set ipmode dhcp 

Then power cycle the iBootBar, or enter the command 

reboot

 

 
To find the address of the iBootBar you will need to query your DHCP server and locate the MAC address of the 
iBootBar in the DHCP server’s IP / MAC table.  You can also access the CLI and use the 

get network

 command. 

 

Содержание iBootBar iBP-N15






















Отзывы: