background image

iBoot Ver 1.5  Page 2  

IMPORTANT SAFETY INSTRUCTIONS

 

 
When using this product, basic safety precautions should always 
be followed to reduce the risk of fire, electric shock, and injury to 
persons, including the following: 

 

1. Read and understand all instructions. 
2. Follow all warnings and marked on the product.  
3. Unplug this product from the wall outlet before cleaning.  Do not use liquid cleaners 

or aerosol cleaners.  Use a damp cloth for cleaning. 

4. Do not use this product in an outdoor environment or near water, for example, near 

a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a 
swimming pool. 

5. Do not place this product on an unstable cart, stand, or table.  The product may fall, 

causing serious damage to the product. 

6. Slots and openings in this product  and the back or bottom are provided for 

ventilation to protect it from overheating, these openings must not be blocked or 
covered.  The openings should never be blocked by placing the product on the bed, 
sofa, rug, or other similar surface.  This product should never be placed near or over 
a radiator or heat register.  This product should not be placed in a built-in installation 
unless proper ventilation is provided. 

7. This product should be operated only from the type of power source indicated on 

the marking label.  If you are not sure of the type of power supply to your home, 
consult your dealer or local power company. 

8. This product is equipped with a three wire grounding type plug, a plug having a third 

(grounding) pin.  This plug will only fit into a grounding type power outlet.  This is a 
safety feature.  If you are unable to insert the plug into the outlet, contact your 
electrician to replace your obsolete outlet.  Do not defeat the safety purpose of the 
grounding type plug.  Do not use a 3-to-2 prong adapter at the receptacle; use of 
this type adapter may result in risk of electrical shock and/or damage to this product. 

9. Do not allow anything to rest on the power cord.  Do not locate this product where 

the cord will be abused by persons walking on it. 

10. Do not overload wall outlets and extension cords as this can result in the risk of fire 

or electric shock.  

11. Never push objects of any kind into this product through slots as they may touch 

dangerous voltage points or short out parts that could result in a risk of fire or 
electrical shock.  Never spill liquid of any kind on the product. 

12. To reduce the risk of electrical shock, do not disassemble this product, but take it to 

a qualified  serviceman when some service or repair work is required.  Opening or 
removing covers may expose you to dangerous voltages or other risks.  Incorrect 
re-assembly can cause electric shock when the appliance is subsequently used.  

13. Unplug this product from the wall outlet and refer servicing to qualified service 

personnel under the following conditions: 

a)   When the power supply cord or plug is damaged or frayed. 
b)   If liquid has been spilled into the product. 
c)  If the product has been exposed to rain or water. 
d)  If the product does not operate normally by following the operating 

instructions.  Adjust only those controls, that are covered by the operating 
instructions because improper adjustment of other controls may result in 
damage and will often require extensive work by a qualified technician to 
restore the product to normal operation. 

e)  If the product has been dropped or has been damaged. 
f)  If the product exhibits a distinct change in performance. 

14.  Avoid using a telephone (other than a cordless type) during an electrical storm.  

There may be a remote risk of electric shock from lightning. 

15.  Do not use the telephone to report a gas leak in the vicinity of the leak. 
16.  Do not exceed the maximum output rating of the auxiliary power receptacle. 
 

SAVE  THESE  INSTRUCTIONS 

Содержание iBoot





















Отзывы: