Datalogic DSM0400 Скачать руководство пользователя страница 18

Страница: 18 / 252

Setup

DSM0400 Fixed Mount Area Imager Bar Code Reader

Relative Size and Location Green Spot

Interface Selection

Upon completing the physical connection between the scanner and its host,

proceed directly to

"Configuring the Interface"

on page 10 for information and

programming for the desired interface type and scan the appropriate bar code

in that section to select your system’s correct interface type.
The scanner, depending upon the model, will support one of the following sets

of host interfaces:

• USB (Keyboard, COM, OEM)
• USB Composite (Ke COM)
• RS-232 STD

For an improved ease of installation, the DSM0400 features a cable auto-rec-

ognition procedure at the startup:

• if a RS232 cable is used, the device will always boot in the RS232 interface

configuration.

• If a USB cable is used the device will always boot in the preferred USB

interface configuration, as descripted in "Configuring the Interface"

(default is USB composite interface). Scan the appropriate barcode for your

reader’s interface type from the following section.

Configuring the Interface

Scan the programming bar code from the following section which selects the

appropriate interface type to match the system the scanner will be connected to.

Next, proceed to the corresponding chapter in this manual (also listed in the table)

to configure any desired settings and features associated with that interface. The

default interface of DSM0400 is USB-Composite

NOTE

Unlike some other programming features and options, interface selections require that you

scan only one programming bar code label. DO NOT scan an ENTER/EXIT Programming

Mode bar code prior to scanning an interface selection bar code.

Thanks to the cable auto-recognition feature, there is no need to scan RS-232 interface
because it is automatically selected at power-up; the RS-232 label is anyway provided for
reference in case of specific needs.

Содержание DSM0400





























































































































































































































































Результаты поиска

Содержание DSM0400

Отзывы:

Похожие инструкции для DSM0400

Бренды по названию

Популярные бренды

Datalogic DSM0400, Руководство по продукции

Результаты поиска

Содержание DSM0400

Отзывы:

Похожие инструкции для DSM0400

Бренды по названию

Популярные бренды