DataApex Colibrick Скачать руководство пользователя страница 14

Страница: 14 / 44

3 Installation

Clarity Hardware

Fig 7: DataApex Colibrick Setup

Enter the detector names in

Name

fields for individual channels, set signal

units.

Note:

A detailed description of this dialog can be found in the chapter

"DataApex Colibrick Setup"

on pg

Press the

button.

The

Colibrick

will appear in the

Setup Control Modules

list

of the

System Configuration

dialog.

Drag and drop the

Colibrick

icon from the

Setup Control Modules

list

the left side of the

System Configuration

dialog to the chosen

Instrument

tab on the right side

(or use the

button

to do so).

Set the

Ext. Start Dig. Input

and

Ready Dig. Output

numbers

for your

acquisition device according to the wires being used for synchronization.

Note:

The configuration dialog of the

) can be displayed any time by double-clicking on its icon or using the

Setup

button.

- 10 -

Содержание Colibrick













































Результаты поиска

Содержание Colibrick

Отзывы:

Похожие инструкции для Colibrick

Бренды по названию

Популярные бренды

DataApex Colibrick, Руководство пользователя

Результаты поиска

Содержание Colibrick

Отзывы:

Похожие инструкции для Colibrick

Бренды по названию

Популярные бренды